DOC AIRBUS | AMM A320FInstallation of the Baby Nursing Table
TASK 25-45-25-400-001-A
Installation of the Baby Nursing Table
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 25-45-25-860-050-A
Subtask 25-45-25-210-050-A
Subtask 25-45-25-862-050-A
[Rev.10 from 2021]
2026.03.31 23:36:36 UTC
Installation of the Baby Nursing Table
ZONE: 200
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
Baby Nursing Table (Lavatory A)Subtask 25-45-25-860-050-A
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
4. Procedure(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
Subtask 25-45-25-210-050-A
A. Preparation for Installation
(1) Clean the component interfaces and the adjacent area.
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
(3) Do an inspection of the component interfaces and the adjacent area.
Subtask 25-45-25-420-050-B (1) Clean the component interfaces and the adjacent area.
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
(3) Do an inspection of the component interfaces and the adjacent area.
B. Installation of the Baby Nursing Table (For Lavatory A only)
(1) Put the tape (1) in position and install the latch (2) with the screws (3).
(2) Put the support (7) in position and install the screws (5) with the washers (6).
(3) Put the baby nursing table (4) in position and install the screws (8) to secure the hinge to the lavatory rear wall.
Subtask 25-45-25-420-051-A (1) Put the tape (1) in position and install the latch (2) with the screws (3).
(2) Put the support (7) in position and install the screws (5) with the washers (6).
(3) Put the baby nursing table (4) in position and install the screws (8) to secure the hinge to the lavatory rear wall.
C. Installation of the Baby Nursing Table
(1) Put the latch (1) in position and install the screws (2).
(2) Put the support (8) in position and install the screws (6) with the washers (7).
(3) Put the baby nursing table (4) in position and install the screws (3) to secure the hinge to the lavatory rear wall.
Subtask 25-45-25-710-050-B (1) Put the latch (1) in position and install the screws (2).
(2) Put the support (8) in position and install the screws (6) with the washers (7).
(3) Put the baby nursing table (4) in position and install the screws (3) to secure the hinge to the lavatory rear wall.
D. Operational Test of the Baby Nursing Table (For Lavatory A only)
(1) Baby nursing table installed on the lavatory rear wall
(a) Open and close the baby nursing table (4) and make sure that the table locks correctly in the closed position, if necessary adjust as follows;
(b) Loosen the screws (3).
(c) Adjust the latch (2) until the baby nursing table (4) locks correctly.
(d) Tigten the screws (3).
Subtask 25-45-25-710-051-A (1) Baby nursing table installed on the lavatory rear wall
(a) Open and close the baby nursing table (4) and make sure that the table locks correctly in the closed position, if necessary adjust as follows;
(b) Loosen the screws (3).
(c) Adjust the latch (2) until the baby nursing table (4) locks correctly.
(d) Tigten the screws (3).
E. Operational Test of the Baby Nursing Table
(1) Baby nursing table installed on the lavatory rear wall
(a) Open and close the baby nursing table (4) and make sure that the table with the hook (5) locks correctly in the closed position, if necessary adjust as follows;
(b) Loosen the screws (2).
(c) Adjust the latch (1) until the baby nursing table (4) locks correctly.
(d) Tigten the screws (2).
5. Close-up(1) Baby nursing table installed on the lavatory rear wall
(a) Open and close the baby nursing table (4) and make sure that the table with the hook (5) locks correctly in the closed position, if necessary adjust as follows;
(b) Loosen the screws (2).
(c) Adjust the latch (1) until the baby nursing table (4) locks correctly.
(d) Tigten the screws (2).
Subtask 25-45-25-862-050-A