DOC AIRBUS | AMM A320FInstallation of the Access Door in the Lavatory
TASK 25-45-18-400-002-A
Installation of the Access Door in the Lavatory
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 25-45-18-860-051-A
Subtask 25-45-18-210-051-A
Subtask 25-45-18-862-051-A
[Rev.10 from 2021]
2026.04.01 06:21:26 UTC
Installation of the Access Door in the Lavatory
ZONE: 200
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
Access Door Inside the LavatorySubtask 25-45-18-860-051-A
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
4. Procedure(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
Subtask 25-45-18-210-051-A
A. Preparation for Installation
(1) Clean the component interfaces and the adjacent area.
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
(3) Do an inspection of the component interfaces and the adjacent area.
Subtask 25-45-18-420-051-A (1) Clean the component interfaces and the adjacent area.
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
(3) Do an inspection of the component interfaces and the adjacent area.
B. Installation of the Access Door Inside the Lavatory
(1) When you connect/install the components, refer to the match marks made during the removal procedure.
(2) Install the pins (3) on the access door (4).
(3) If you removed the bushes (2), put them in position.
(4) Put the access door (4) in position.
(5) Put the bracket (7) in position and install the washers (8), the screws (9) and the nuts (6).
(6) Tighten the nuts (6).
(7) Close the access door (4).
Subtask 25-45-18-710-051-A (1) When you connect/install the components, refer to the match marks made during the removal procedure.
(2) Install the pins (3) on the access door (4).
(3) If you removed the bushes (2), put them in position.
(4) Put the access door (4) in position.
(5) Put the bracket (7) in position and install the washers (8), the screws (9) and the nuts (6).
(6) Tighten the nuts (6).
(7) Close the access door (4).
C. Operational Test of the Access Door Inside the Lavatory
(1) Open and close the access door (4) and make sure that it locks correctly.
(2) If necessary, adjust the access door (4) as follows:
(a) Turn the pins (3) to adjust the position of the access door (4) until the access door (4) locks correctly.
(b) Close the access door (4).
5. Close-up(1) Open and close the access door (4) and make sure that it locks correctly.
(2) If necessary, adjust the access door (4) as follows:
(a) Turn the pins (3) to adjust the position of the access door (4) until the access door (4) locks correctly.
(b) Close the access door (4).
Subtask 25-45-18-862-051-A