DOC AIRBUS | AMM A320FRepair of the Toilet Seat
TASK 25-40-00-340-003-A
Repair of the Toilet Seat
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Referenced Information
3. Job Set-up
Subtask 25-40-00-861-063-A 4. Procedure
Subtask 25-40-00-340-053-A
Subtask 25-40-00-942-056-A
[Rev.10 from 2021]
2026.03.31 23:35:01 UTC
Repair of the Toilet Seat
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | CLOTH-EMERY (GRADE 320 - 400) |
| No specific | 1 | WARNING NOTICE(S) |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.05GBH1) | Cyanoacrylate Adhesive-Non Structural One Part - Low viscosity - |
| (Material No.08BBD1) | Non Aqueous Cleaner-- Isopropyl Alcohol - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| No specific | Buffer PN 11593 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
Toilet SeatSubtask 25-40-00-861-063-A 4. Procedure
Subtask 25-40-00-340-053-A
A. Repair of the Toilet Seat (Buffer Replacement)
(2) Remove the old adhesive from the toilet seat (2) wit a CLOTH-EMERY (GRADE 320 - 400).
(3) Use the Non Aqueous Cleaner-- Isopropyl Alcohol - (Material No.08BBD1) and a lint-free cotton cloth Textile-Lint free Cotton - (Material No.14SBA1) to clean the area to be repaired on the toilet seat (2).
(4) Apply the Cyanoacrylate Adhesive-Non Structural One Part - Low viscosity - (Material No.05GBH1) to the surface of the new Buffer PN 11593 (3) to be bonded.
(5) Install the new buffer (3) on the toilet seat (2).
(7) Lower the toilet seat (2) and make sure the fit between the seat (2) and the toilet shroud (4) is correct.
(8) Put the WARNING NOTICE(S) in position to tell persons not to use the toilet seat for approximately 1 hour.
(9) Carefully lower the toilet seat cover (1).
5. Close-upWARNING:
ALWAYS WEAR RUBBER GLOVES, GOGGLES AND PROTECTIVE CLOTHES WHEN YOU DO THIS TASK.
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
(1) Lift the toilet seat cover (1) and the toilet seat (2). (2) Remove the old adhesive from the toilet seat (2) wit a CLOTH-EMERY (GRADE 320 - 400).
(3) Use the Non Aqueous Cleaner-- Isopropyl Alcohol - (Material No.08BBD1) and a lint-free cotton cloth Textile-Lint free Cotton - (Material No.14SBA1) to clean the area to be repaired on the toilet seat (2).
(4) Apply the Cyanoacrylate Adhesive-Non Structural One Part - Low viscosity - (Material No.05GBH1) to the surface of the new Buffer PN 11593 (3) to be bonded.
(5) Install the new buffer (3) on the toilet seat (2).
NOTE: The minimum time for the adhesive to bond is 1 minute at 23 +3 deg.C or -3 deg.C (73.40 +5.40 deg.F or -5.40 deg.F).
(6) Use the Textile-Lint free Cotton - (Material No.14SBA1) and a lint-free cotton cloth Non Aqueous Cleaner-- Isopropyl Alcohol - (Material No.08BBD1) to remove any unwanted adhesive. (7) Lower the toilet seat (2) and make sure the fit between the seat (2) and the toilet shroud (4) is correct.
(8) Put the WARNING NOTICE(S) in position to tell persons not to use the toilet seat for approximately 1 hour.
(9) Carefully lower the toilet seat cover (1).
Subtask 25-40-00-942-056-A
A. Close-up
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Subtask 25-40-00-862-064-A (1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.