Removal of the Coffee Maker(s)

TASK 25-35-15-000-001-A
Removal of the Coffee Maker(s)

WARNING: BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY (MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.

ZONE: 200

1. Reason for the Job
Self Explanatory

NOTE: More than one person is necessary for this procedure.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	CAP - BLANKING
No specific	AR	PLUG - BLANKING
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
200	UPPER HALF FUSELAGE

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 38-10-00-614-002-A	Depressurization of the Potable Water System
Coffee Maker attached with screws
Coffee Maker attached with single release pin

3. Job Set-up
Subtask 25-35-15-861-052-A ** ON A/C NOT FOR ALL

A. Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).

Subtask 25-35-15-860-050-A ** ON A/C NOT FOR ALL

B. Aircraft Maintenance Configuration
(1) Depressurize the potable water system (Ref. AMM TASK 38-10-00-614-002).
(2) On the water service panel, put the WARNING NOTICE(S) in position to tell persons not to pressurize the potable water system.

Subtask 25-35-15-860-058-A ** ON A/C NOT FOR ALL

C. At the applicable galley, on the galley control panel, open, safety and tag the related circuit breaker(s) of the coffee maker(s).

4. Procedure
Subtask 25-35-15-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the Coffee Maker (attached with screws)

Coffee Maker attached with screws ** ON A/C NOT FOR ALL

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

(1) Remove the screws (1).
(2) Removal of the coffee maker from the galley

WARNING: MAKE SURE THAT THE POTABLE WATER SYSTEM IS DEPRESSURIZED. A PRESSURIZED SYSTEM CAN CAUSE INJURY TO PERSONS WHEN THEY DO WORK ON IT.

(a) Carefully pull the coffee maker (2) to disconnect the electrical connectors and the potable-water supply line.
(b) Remove the coffee maker (2) from the galley.
(3) Put CAP - BLANKING on the disconnected electrical connectors.
(4) Put PLUG - BLANKING on the disconnected line ends.

Subtask 25-35-15-020-051-A ** ON A/C NOT FOR ALL

B. Removal of the Coffee Maker (Attached with a Single Release Pin)

Coffee Maker attached with single release pin ** ON A/C NOT FOR ALL

WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

WARNING: SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.

(1) Prevent damage to the component interfaces and the adjacent area.
(2) Set the lever (1) to the unlocked position.
(3) Remove the coffee maker (2) from the galley as follows:

WARNING: MAKE SURE THAT THE POTABLE WATER SYSTEM IS DEPRESSURIZED. A PRESSURIZED SYSTEM CAN CAUSE INJURY TO PERSONS WHEN THEY DO WORK ON IT.

(a) Carefully pull the coffee maker (2) out of the galley and disconnect the electrical connector, the water supply line and the drain line.
(b) Remove the coffee maker (2) from the mounting rails (3).
(4) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(5) Put the PLUG-BLANKING in each disconnected line end.

[Rev.10 from 2021] 2026.04.01 06:12:41 UTC