DOC AIRBUS | AMM A320FInstallation of the Mirror
TASK 25-24-41-400-803-A
Installation of the Mirror
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Referenced Information
3. Job Set-up
Subtask 25-24-41-860-060-A ** ON A/C NOT FOR ALL
Subtask 25-24-41-420-069-A ** ON A/C NOT FOR ALL
Subtask 25-24-41-860-061-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:32:13 UTC
Installation of the Mirror
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | SCRAPER - NON METALLIC |
| No specific | AR | STEPLADDER 0.5 M (1.6 FT) |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.08BBD1) | Non Aqueous Cleaner-- Isopropyl Alcohol - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
Subtask 25-24-41-860-060-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the STEPLADDER 0.5 M (1.6 FT) is near the related Overhead Stowage Compartment (OHSC).
(3) Make sure that the equipment is removed from the OHSC.
4. Procedure(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the STEPLADDER 0.5 M (1.6 FT) is near the related Overhead Stowage Compartment (OHSC).
(3) Make sure that the equipment is removed from the OHSC.
Subtask 25-24-41-420-069-A ** ON A/C NOT FOR ALL
A. Installation of the Mirror
(1) When you connect/install the components, refer to the match marks made during the removal procedure.
(2) Clean the area of installation with Non Aqueous Cleaner-- Isopropyl Alcohol - (Material No.08BBD1) , a Textile-Lint free Cotton - (Material No.14SBA1) and a SCRAPER - NON METALLIC.
(3) Remove the protective film from the adhesive tape on the rear of the mirror.
(4) Carefully put the mirror in position.
(6) Make sure that you have a satisfactory view.
(7) Clean the surface of the mirror with a Textile-Lint free Cotton - (Material No.14SBA1) .
5. Close-up(1) When you connect/install the components, refer to the match marks made during the removal procedure.
(2) Clean the area of installation with Non Aqueous Cleaner-- Isopropyl Alcohol - (Material No.08BBD1) , a Textile-Lint free Cotton - (Material No.14SBA1) and a SCRAPER - NON METALLIC.
(3) Remove the protective film from the adhesive tape on the rear of the mirror.
(4) Carefully put the mirror in position.
NOTE: The mirror is not easy to move or remove after installation. Thus, put the mirror carefully in position before installation.
(5) Push the mirror tightly with a force of more than 5 kilogram/square centimeter (71.12 pound-force/square inch). (6) Make sure that you have a satisfactory view.
(7) Clean the surface of the mirror with a Textile-Lint free Cotton - (Material No.14SBA1) .
Subtask 25-24-41-860-061-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Install all items of equipment removed from the OHSC.
(2) Remove the stepladder.
(3) Make sure that the work area is clean and clear of tools and other items.
(4) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).
(1) Install all items of equipment removed from the OHSC.
(2) Remove the stepladder.
(3) Make sure that the work area is clean and clear of tools and other items.
(4) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).