Installation of the Captain (First Officer) Seat-Headrest Assy
TASK 25-11-64-400-001-A
Installation of the Captain (First Officer) Seat-Headrest Assy
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 25-11-64-860-050-A
Subtask 25-11-64-420-050-A
Subtask 25-11-64-862-050-A
[Rev.10 from 2021]
2026.04.01 06:01:28 UTC
Installation of the Captain (First Officer) Seat-Headrest Assy
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 211 | COCKPIT |
| 212 | COCKPIT |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
Subtask 25-11-64-860-050-A
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
4. Procedure(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
Subtask 25-11-64-420-050-A
A. Installation of the Captain (First Officer) Seat-Headrest Assy
(1) Clean the component interfaces and the adjacent area.
(2) Put the lower strap guide (10) in position on the harness support (11).
(3) Put the two inserts (9) in position on the lower strap guide (10).
(4) Put the upper strap guide (8) in position and install the three screws (12), the washers (13) and the reinforcement fitting (14).
(5) Tighten the three screws (12).
(6) Install the headrest clips (7) on the upper strap guide (8).
(7) Push the lumbar rest control-knobs (3) to install them.
(8) Install the retainer rings (2).
(9) Put the upper back shroud (4) of the backrest in position on the seat (1) and install the fourteen screws (5).
(10) Tighten the fourteen screws (5).
(11) Put the headrest (6) in position in the guides of the seat (1) and push it in.
(12) Make sure it is only necessary to push or pull the headrest (6) to adjust it to the correct position (up, down or reclined).
5. Close-up(1) Clean the component interfaces and the adjacent area.
(2) Put the lower strap guide (10) in position on the harness support (11).
(3) Put the two inserts (9) in position on the lower strap guide (10).
(4) Put the upper strap guide (8) in position and install the three screws (12), the washers (13) and the reinforcement fitting (14).
(5) Tighten the three screws (12).
(6) Install the headrest clips (7) on the upper strap guide (8).
(7) Push the lumbar rest control-knobs (3) to install them.
(8) Install the retainer rings (2).
(9) Put the upper back shroud (4) of the backrest in position on the seat (1) and install the fourteen screws (5).
(10) Tighten the fourteen screws (5).
(11) Put the headrest (6) in position in the guides of the seat (1) and push it in.
(12) Make sure it is only necessary to push or pull the headrest (6) to adjust it to the correct position (up, down or reclined).
Subtask 25-11-64-862-050-A
Captain (First Officer) Seat-Headrest Assy