W DOC AIRBUS | AMM A320F

Lubrication of Rudder Hinge Bearing No. 6 with Grease MAT. No. 04-037 (or Grease MAT. No. 03GBC1)

TASK 12-22-55-640-002-A
Lubrication of Rudder Hinge Bearing No. 6 with Grease MAT. No. 04-037 (or Grease MAT. No. 03GBC1)

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 325
1. Reason for the Job
Refer to the MPD TASK: 272400-05
LUBRICATION OF RUDDER HINGE BEARING NO 6 WITH GREASE MAT. NO. 04-037
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 10M (33 FT) - ADJUSTABLE
No specific
1
GUN - GREASE
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
1
WARNING NOTICE(S)
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.03GBC1)
Synthetic Oil base Grease-General Purpose Lithium Thickened Low Temp. -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
325
VERTICAL STABILIZER TRAILING EDGE
325DL
325FR, 325GR
325DR
 D. Referenced Information
REFERENCE
DESIGNATION
TASK 29-10-00-864-001-A
Depressurize the Green Hydraulic System
TASK 29-10-00-864-002-A
Depressurize the Yellow Hydraulic System
TASK 29-10-00-864-003-A
Depressurize the Blue Hydraulic System
TASK 55-33-13-010-002-A
Opening/Removal of the Trailing Edge Access-Panels of the Vertical Stabilizer
TASK 55-33-13-410-002-A
Closing/Installation of the Trailing Edge Access-Panels of the Vertical Stabilizer
TASK 12-22-00-00
LUBRICATION - DESCRIPTION AND OPERATION
F Rudder Hinge Bearing No. 6
3. Job Set-up
Subtask 12-22-55-010-052-A ** ON A/C NOT FOR ALL
A. Get Access
   (1) Depressurize the Green, Yellow and Blue hydraulic systems (Ref. AMM TASK 29-10-00-864-001), (Ref. AMM TASK 29-10-00-864-002) and (Ref. AMM TASK 29-10-00-864-003).
   (2) Put the WARNING NOTICE(S) in position in the cockpit to tell persons not to operate the flight controls.
   (3) Put the ACCESS PLATFORM 10M (33 FT) - ADJUSTABLE in position at zone 325.
   (4) Open and safety access panel 325DL or 325DR (Ref. AMM TASK 55-33-13-010-001).
Subtask 12-22-55-010-052-B ** ON A/C NOT FOR ALL
A. Get Access
   (1) Depressurize the Green, Yellow and Blue hydraulic systems (Ref. AMM TASK 29-10-00-864-001), (Ref. AMM TASK 29-10-00-864-002) and (Ref. AMM TASK 29-10-00-864-003).
   (2) Put the WARNING NOTICE(S) in position in the cockpit to tell persons not to operate the flight controls.
   (3) Put the ACCESS PLATFORM 10M (33 FT) - ADJUSTABLE in position at zone 325.
   (4) Open and safety access panel 325DL (Ref. AMM TASK 55-33-13-010-002).
   (5) Remove access panels 325FR and 325GR (Ref. AMM TASK 55-33-13-010-002).
Subtask 12-22-55-865-052-A
B. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B09
49VUAUTO FLT/FAC1/28VDC5CC1B04
49VUAUTO FLT/FAC1/26VAC14CC1B03
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B04
49VUAUTO FLT/FAC1/28VDC5CC1H10
49VUAUTO FLT/FAC1/26VAC14CC1H09
** ON A/C ALL
121VUAUTO FLT/RUDDER/TRIM/IND15CCM20
121VUAUTO FLT/FAC2/28VDC5CC2M19
121VUAUTO FLT/FAC2/26VAC14CC2M18
121VUFLIGHT CONTROLS/THS ACTR/MOT319CE3Q17
121VUFLIGHT CONTROLS/THS ACTR/MOT119CE1Q16
4. Procedure
Subtask 12-22-55-640-051-A
A. Lubrication of the Rudder Hinge Bearing No. 6.
F Rudder Hinge Bearing No. 6
   (1) Airbus recommends you to remove the grease from the bearing before its lubrication.
NOTE: For grease specification and lubrication requirements, refer to (Ref. AMM D/O 12-22-00-00).
   (2) Clean the grease nipple with the Textile-Lint free Cotton - (Material No.14SBA1) .
   (3) Lubricate the bearing with Synthetic Oil base Grease-General Purpose Lithium Thickened Low Temp. - (Material No.03GBC1) through the grease nipple with the GUN - GREASE.
   (4) Remove the unwanted grease with the Textile-Lint free Cotton - (Material No.14SBA1) .
5. Close-up
Subtask 12-22-55-410-052-A ** ON A/C NOT FOR ALL
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Close access panel 325DL or 325DR (Ref. AMM TASK 55-33-13-410-001).
   (3) Remove the WARNING NOTICE(S).
   (4) Remove the access platform(s).
Subtask 12-22-55-410-052-B ** ON A/C NOT FOR ALL
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Install access panels 325FR and 325GR (Ref. AMM TASK 55-33-13-410-002).
   (3) Close access panel 325DL (Ref. AMM TASK 55-33-13-410-002).
   (4) Remove the WARNING NOTICE(S).
   (5) Remove the access platform(s).
Subtask 12-22-55-865-053-A
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B09
49VUAUTO FLT/FAC1/28VDC5CC1B04
49VUAUTO FLT/FAC1/26VAC14CC1B03
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B04
49VUAUTO FLT/FAC1/28VDC5CC1H10
49VUAUTO FLT/FAC1/26VAC14CC1H09
** ON A/C ALL
121VUAUTO FLT/RUDDER/TRIM/IND15CCM20
121VUAUTO FLT/FAC2/28VDC5CC2M19
121VUAUTO FLT/FAC2/26VAC14CC2M18
121VUFLIGHT CONTROLS/THS ACTR/MOT319CE3Q17
121VUFLIGHT CONTROLS/THS ACTR/MOT119CE1Q16
[Rev.10 from 2021] 2026.03.31 22:57:05 UTC
"Aviabrain" 2025