Replenish Oil System

TASK 12-13-80-610-002-B
Replenish Oil System

ZONE: 436
ZONE: 446

1. Reason for the Job
Refer to the MPD TASK: 801110-C2
REPLENISH OIL SYSTEM
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.CP2442)	engine oil

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
436	FAN AND ACCESSORY GEARBOX
446	FAN AND ACCESSORY GEARBOX
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

D. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
20	O-RING	AIPC 80-11-10-01-130
30	O-RING	AIPC 80-11-10-01-130

E. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
TASK 80-11-10-000-002-A	Removal of the Pneumatic Starter
TASK 80-11-10-400-002-A	Installation of the Pneumatic Starter
Pneumatic Starter Servicing

3. Job Set-up
Subtask 12-13-80-941-053-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 12-13-80-010-053-A ** ON A/C NOT FOR ALL

B. Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR

4. Procedure
Subtask 12-13-80-010-054-A ** ON A/C NOT FOR ALL

A. Remove the filler plug:
(1) Remove the filler plug (10), and overflow plug (40). Push inward and simultaneously turn counter clockwise to disengage locking device. Discard O-rings (20 and 30).

Subtask 12-13-80-610-050-A ** ON A/C NOT FOR ALL

B. Fill the starter housing

CAUTION: BE CAREFUL NOT TO OVERFILL THE STARTER. IF YOU PUT TOO MUCH OIL IN THE STARTER, DAMAGE TO THE ENGINE CAN OCCUR.

(1) Fill the starter housing with engine oil (Material No.CP2442) through the filler port until the oil flows from the overflow port.

NOTE: The added quantity of oil should be less than 0.32 quart (approximately 0.3 liter). If the quantity is more than 0.32 quart, replace the starter (Ref. AMM TASK 80-11-10-000-002) and (Ref. AMM TASK 80-11-10-400-002)

Subtask 12-13-80-410-053-A ** ON A/C NOT FOR ALL

C. Install the filler plug:
(1) Clean the filler plug (10) and overflow plug (40). Apply a thin layer of engine oil (Material No.CP2442) on the new AIPC 80-11-10-01-130 O-RING (20) and AIPC 80-11-10-01-130 O-RING (30), and install the new O-ring on the filler plug and the overflow plug.
(2) Install the filler plug (10) and overflow plug (40) push inward and simultaneously turn clockwise to engage locking device.

5. Close-up
Subtask 12-13-80-410-054-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors: (Ref. AMM TASK 71-13-00-410-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.03.31 22:55:46 UTC