EEC Internal Failure Level B

TASK 73-21-00-810-870-A
EEC Internal Failure Level B

1. Possible Causes

[4000KS]

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
TSM TASK 71-00-00-810-834-A	General Troubleshooting Guidelines for Additional Troubleshooting Information
TSM TASK 71-00-00-810-835-A	Component and Harness Intermittent Troubleshooting Procedure for Guidance Troubleshooting Intermittent Faults
AMM 24-41-00-861-002	Energize the Aircraft Electrical Circuits from the External Power
AMM 24-41-00-862-002	De-energize the Aircraft Electrical Circuits Supplied from the External Power
AMM 73-21-01-000-801	Removal of the Electronic Engine Control (EEC)
AMM 73-21-01-400-801	Installation of the Electronic Engine Control (EEC)
EEC Wiring Harnesses

3. Fault Confirmation
Subtask 73-21-00-710-121-A ** ON A/C NOT FOR ALL

A. Energize the FADEC of the engine that has a fault report.
(1) Energize the aircraft electrical circuits AMM 24-41-00-861-002.
(2) On the ENG section of maintenance panel 50VU:
(a) Release the FADEC GND PWR/1(2) pushbutton switch (the ON legend comes on).

NOTE: After the FADEC is energized, wait ten seconds before you start the test. If you do not wait ten seconds, the interactive mode stops the EEC self-test and this can cause spurious faults.

(3) On Multipurpose Control and Display Unit (MCDU) screen, check if the fault is displayed on ground scanning report.

NOTE: The Electronic Engine Control (EEC) has detected an internal failure that is short time dispatch (MMEL). The EEC is attached to the fan case assembly, located at the 2 o'clock position.

Refer to the general troubleshooting guidelines for additional troubleshooting information (Ref. TSM TASK 71-00-00-810-834).
Refer to the component and harness intermittent troubleshooting procedure for guidance troubleshooting intermittent faults (Ref. TSM TASK 71-00-00-810-835).

(4) If the maintenance message does not come back, examine the harnesses and electrical connector as describe in the component and harness intermittent fault isolation procedure (Ref. TSM TASK 71-00-00-810-835).
(a) If no problems are found, return the engine to service. Monitor the engine for reoccurring maintenance message.
(5) If the maintenance message comes back (hard fault) in channel A or channel B, go to the Para. Fault Isolation.

4. Fault Isolation

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS WARNING, INJURY CAN OCCUR.

WARNING: REFER TO THE MSDS FOR ALL MATERIAL USED AND THE MANUFACTURER'S SAFETY INSTRUCTIONS FOR ALL EQUIPMENT USED. IF YOU DO NOT OBEY THIS WARNING, INJURY CAN OCCUR.

CAUTION: MAKE SURE YOU REMOVE ELECTRICAL POWER FROM THE EEC BEFORE YOU REMOVE THE ELECTRICAL CONNECTORS. IF YOU DO NOT OBEY THIS INSTRUCTION, DAMAGE TO THE EEC CAN OCCUR.

Subtask 73-21-00-810-142-A ** ON A/C NOT FOR ALL

A. If there is confirmation of the fault:
(1) Replace [4000KS] AMM 73-21-01-000-801 and AMM 73-21-01-400-801.
(a) Do the test given in Para. 3.

5. Close-up
Subtask 73-21-00-860-062-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tools and other items.
(a) De-energize the aircraft electrical circuits AMM 24-41-00-862-002.

[Rev.8 from Aug 2018] 2026.04.04 04:36:39 UTC