IDG FOC Delta Pressure Sensor Electrical Failure Channel B

TASK 71-00-00-810-837-A
IDG FOC Delta Pressure Sensor Electrical Failure Channel B

1. Possible Causes

SENSOR-DIFF PRESS, IDG FUEL/OIL HEAT [9XT]
W03 HARNESS [4087KS]
W04 HARNESS [4088KS]
HARNESS-CORE,WC11 [4072KS]
[4000KS]

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	MULTIMETER - STANDARD
No specific	1	PLIERS - JAWED, SOFT

B. Referenced Information

REFERENCE	DESIGNATION
TSM TASK 71-00-00-810-834-A	General Troubleshooting Guidelines for Additional Troubleshooting Information
TSM TASK 71-00-00-810-835-A	Component and Harness Intermittent Troubleshooting Procedure for Guidance Troubleshooting Intermittent Faults
AMM 24-21-42-000-804	Removal of the AC Generator Fuel/Oil Differential Pressure-Sensor
AMM 24-21-42-400-804	Installation of the AC Generator Fuel/Oil Differential Pressure-Sensor
AMM 70-70-00-910-803	SPOP 6 - Cleaning of the Contact Points and Wiring Harnesses
AMM 73-21-00-710-806	Test No.7 - EEC Operation Test (Self Test)
AMM 73-21-01-000-801	Removal of the Electronic Engine Control (EEC)
AMM 73-21-01-400-801	Installation of the Electronic Engine Control (EEC)
AMM 73-21-63-000-802	Removal of the Electronic Engine Control (EEC) Wiring Harness (W03)
AMM 73-21-63-400-802	Installation of the Electronic Engine Control (EEC) Wiring Harness (W03)
AMM 73-21-64-000-802	Removal of the Electronic Engine Control (EEC) Wiring Harness (W04)
AMM 73-21-64-400-802	Installation of the Electronic Engine Control (EEC) Wiring Harness (W04)
AMM 73-21-70-000-802	Removal of the Electronic Engine Control (EEC) Wiring Harness (WC11)
AMM 73-21-70-400-802	Installation of the Electronic Engine Control (EEC) Wiring Harness (WC11)
AMM 78-36-00-010-802	Opening of the Thrust Reverser Cowl-Doors
AMM 78-36-00-410-802	Closing of the Thrust Reverser Cowl-Doors
EEC Wiring Harnesses
W04/WC11 Interconnect Wiring Harness
AC Generator Fuel/Oil Cooler DP Sensor Wiring Harness
AC Generator Fuel/Oil Cooler DP Sensor Wiring Schematic
W03/W04 Interconnect Wiring Harness

3. Fault Confirmation
Subtask 71-00-00-710-089-A ** ON A/C NOT FOR ALL

A. Do the EEC system interactive test to confirm this fault. Refer to FADEC self test AMM 73-21-00-710-806.

NOTE: The Electronic Engine Control (EEC) has detected the circuit for AC generator Fuel Oil Cooler (FOC) Differential Pressure (DP) Sensor (SNSR) is out of range or rate in channel B. The AC generator FOC DP sensor is mounted on the oil control module, located at the 9 o'clock position.

Refer to the general troubleshooting guidelines for additional troubleshooting information (Ref. TSM TASK 71-00-00-810-834).
Refer to the component and harness intermittent troubleshooting procedure for guidance troubleshooting intermittent faults (Ref. TSM TASK 71-00-00-810-835).

(1) If the maintenance message does not come back, examine the harnesses and electrical connectors as described in the component and harness intermittent fault isolation procedure (Ref. TSM TASK 71-00-00-810-835).
(a) If no problems are found, return the engine to service. Monitor the engine for reoccurring maintenance message.
(2) If the maintenance message comes back (hard fault) in channel B, go to the Para. Fault Isolation.

4. Fault Isolation

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS WARNING, INJURY CAN OCCUR.

WARNING: REFER TO THE MSDS FOR ALL MATERIAL USED AND THE MANUFACTURER'S SAFETY INSTRUCTIONS FOR ALL EQUIPMENT USED. IF YOU DO NOT OBEY THIS WARNING, INJURY CAN OCCUR.

CAUTION: MAKE SURE YOU REMOVE ELECTRICAL POWER FROM THE EEC BEFORE YOU REMOVE THE ELECTRICAL CONNECTORS. IF YOU DO NOT OBEY THIS INSTRUCTION, DAMAGE TO THE EEC CAN OCCUR.

Subtask 71-00-00-810-101-A ** ON A/C NOT FOR ALL

A. If there is confirmation of the fault:
(1) Open the thrust reverser cowl-doors AMM 78-36-00-010-802.
(2) Examine the W03 (4087KS), W04 (4088KS) and WC11 (4072KS) harnesses and connector P6 (4000KS-P6) - EEC (4000KS), interconnect P106 (4100VC-A)/J106 (4100VC), interconnect J105 (4108VC)/P105 (4108VC-A) and connector P37 (9XT-P37) - AC Generator FOC DP sensor (9XT), for problems which are possible between EEC (4000KS) and the AC Generator FOC DP sensor (9XT).
(a) Inspect for harness damage.
(b) Inspect for loose or damaged connectors.

NOTE: Loose connectors must be disconnected and examined for further wear or damage.

(c) If a problem is found with the harnesses or connectors:
1 Replace W03 HARNESS(4087KS) AMM 73-21-63-000-802 and AMM 73-21-63-400-802, or
2 Replace W04 HARNESS(4088KS) AMM 73-21-64-000-802 and AMM 73-21-64-400-802, or
3 Replace WC11 HARNESS-CORE(4072KS) AMM 73-21-70-000-802 and AMM 73-21-70-400-802.
4 Do the test given in Para. 3.
(3) If no problems are found with the harness, use a PLIERS - JAWED, SOFT to disconnect electrical connector P6 (4000KS-P6) from the EEC (4000KS), interconnect P106 (4100VC-A)/J106 (4100VC), interconnect J105 (4108VC)/P105 (4108VC-A) and connector P37 (9XT-P37) from the AC generator FOC DP sensor (9XT).
(a) Examine the pins and sockets (contacts) for alignment and damage. Look for contacts pushed rearward into the connector face. Replace parts as necessary.
(b) Clean the contacts with contact cleaner and clean cloth per SPOP 6. Blow dry with air (at less than 30 psi) across the connector face AMM 70-70-00-910-803.
(c) Reconnect electrical connector P6 (4000KS-P6) to the EEC (4000KS), interconnect P106 (4100VC-A)/J106 (4100VC), interconnect J105 (4108VC)/P105 (4108VC-A) and connector P37 (9XT-P37) to the AC generator FOC DP sensor (9XT).
(d) Do the test given in Para. 3.
(4) If the fault continues:
(a) Replace SENSOR-DIFF PRESS, IDG FUEL/OIL HEAT [9XT] AMM 24-21-42-000-804 and AMM 24-21-42-400-804.
(b) Do the test given in Para. 3.
(5) If the fault continues:
(a) Disconnect electrical connector P6 (4000KS-P6) from the EEC (4000KS), interconnect P106 (4100VC-A)/J106 (4100VC), interconnect J105 (4108VC)/P105 (4108VC-A) and connector P37 (9XT-P37) from the AC generator FOC DP sensor (9XT). Use a MULTIMETER - STANDARD to test the AC generator FOC DP sensor (9XT) circuits in the harnesses. Refer to Table 1. Look for:
1 Wire-to-wire shorts
2 Shorts to ground
3 Continuity (less than 5 ohms resistance).

NOTE: A short to ground is found when the resistance is less than 100 000 (100K) ohms.

Table 1: AC Generator Fuel/Oil Cooler DP Sensor Channel B Connector Contacts

W03(4087KS) Harness P6 (4000KS-P6) EEC(4000KS) Connector Contacts	W03(4087KS) Harness P106 (4100VC-A) Connector Contacts	W04(4088KS) Harness J106 (4100VC) Connector Contacts	W04(4088KS) Harness J105 (4108VC) Connector Contacts	WC11(4072KS) Harness P105 (4108VC-A) Connector Contacts	WC11(4072KS) Harness P37 (9XT-P37) AC Generator FOC DP SNSR (9XT) Connector Contacts
z	13	13	5	5	9
L	29	29	6	6	8
i	27	27	7	7	7
j	28	28	8	8	6

(b) If a problem is found with the harnesses or connectors:
1 Replace W03 HARNESS [4087KS] AMM 73-21-63-000-802 and AMM 73-21-63-400-802, or
2 Replace W04 HARNESS [4088KS] AMM 73-21-64-000-802 and AMM 73-21-64-400-802, or
3 Replace HARNESS-CORE,WC11 [4072KS] AMM 73-21-70-000-802 and AMM 73-21-70-400-802.
4 Do the test given in Para. 3.
(6) If the fault continues:
(a) Replace [4000KS] AMM 73-21-01-000-801 and AMM 73-21-01-400-801.
(b) Do the test given in Para. 3.

5. Close-up
Subtask 71-00-00-860-051-A ** ON A/C NOT FOR ALL

A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tools and other items.
(a) Close the thrust reverser cowl-doors AMM 78-36-00-410-802.

[Rev.8 from Aug 2018] 2026.04.04 04:35:02 UTC