W DOC AIRBUS | TSM A320F

Failure of ELAC1 (PIN PROG)

TASK 27-93-00-810-956-A
Failure of ELAC1 (PIN PROG)

1. Possible Causes
  • ELAC-1 [2CE1]
  • wiring of the DGO 04 signal
  • wiring of the DSI 39 signal at pin AA/12J (COM part) and pin AD/15E (MON part)
  • wirings of the DSI 39 and 47 signals
  • wiring of the DSI 20 signal
  • wirings of the DSI 20 and 43 signals
  • wiring of the DSI 43 signal
  • wirings of the DSI 20, 39 and 47 signals
  • wiring of the DSI 47 signal
  • wirings of the DSI 20, 22, 39 and 43 signals
2. Job Set-up Information
 A. Referenced Information
REFERENCE
DESIGNATION
TSM TASK 27-93-00-810-896-A
Failure of ELAC1
AMM 24-41-00-861-002
Energize the Aircraft Electrical Circuits from the External Power
ASM 279240
ASM 279250
AMM 27-93-34-000-001
Removal of the ELAC
AMM 27-93-34-400-001
Installation of the ELAC
AMM 27-96-00-740-001
BITE Test of the EFCS (Ground Scanning)
3. Fault Confirmation
Subtask 27-93-00-860-085-A
A. Job Set-Up
   (1) Energize the aircraft electrical circuits AMM 24-41-00-861-002.
   (2) Make sure that the hydraulic systems are depressurized.
   (3) On the overhead panel 23VU:
  • release the FLT CTL/ELAC 1 pushbutton switch (the OFF legend of the FLT CTL/ELAC1 pushbutton switch comes on).
   (4) On the overhead panel 23VU:
  • push the FLT CTL/ELAC 1 pushbutton switch (the OFF legend of the FLT CTL/ELAC1 pushbutton switch goes off).
NOTE: In case of a reset of the ELAC 1 with the circuit breaker, the supply breaking must be more than 5 seconds.
NOTE: If the ELAC FAULT warning disappears after several resets, replace the computer.
Subtask 27-93-00-740-200-A
B. Test
   (1) Do the BITE test of the EFCS (Ground Scanning) AMM 27-96-00-740-001.
4. Fault Isolation
Subtask 27-93-00-810-289-A ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check and repair the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
   (3) If the fault continues:
Subtask 27-93-00-810-289-C ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check for an open circuit of the wiring of the DSI 39 signal at pin AA/12J (COM part) and pin AD/15E (MON part) of ELAC1 (2CE1) ASM 279240.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (4) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-D ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check for an open circuit of the wirings of the DSI 39 and 47 signals from the ELAC1 (2CE1) COM part and the MON part ASM 279240:
  • For DSI 39: pin AA/12J (COM part) and pin AD/15E (MON part).
  • For DSI 47: pin AA/5K (COM part) and pin AD/13H (MON part).
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (4) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-E ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check of the wiring of the DSI 20 signal from the ELAC1 (2CE1) COM part and the MON part to the ground terminal ASM 279240.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (4) Do a check for an open circuit of the wiring of the DSI 39 signal at pin AA/12J (COM part) and pin AD/15E (MON part) of ELAC1 (2CE1) ASM 279240.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (5) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-G ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check of the wirings of the DSI 20 and 43 signals from the ELAC1 (2CE1) COM part and the MON part to the ground terminal ASM 279240.
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (4) Do a check for an open circuit of the wiring of the DSI 39 signal at pin AA/12J (COM part) and pin AD/15E (MON part) of ELAC1 (2CE1) ASM 279240.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (5) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-N ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check of the wiring of the DSI 20 signal from the ELAC1 (2CE1) COM part and the MON part to the ground terminal ASM 279240.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (4) Do a check for an open circuit of the wirings of the DSI 39 and 47 signals from the ELAC1 (2CE1) COM part and the MON part ASM 279240.
  • For DSI 39: pin AA/12J (COM part) and pin AD/15E (MON part).
  • For DSI 47: pin AA/5K (COM part) and pin AD/13H (MON part).
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (5) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-R ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check of the wirings of the DSI 20 and 43 signals from the ELAC1 (2CE1) COM part and the MON part to the ground terminal ASM 279240.
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (4) Do a check for an open circuit of the wirings of the DSI 39 and 47 signals from the ELAC1 (2CE1) COM part and the MON part ASM 279240:
  • For DSI 39: pin AA/12J (COM part) and pin AD/15E (MON part).
  • For DSI 47: pin AA/5K (COM part) and pin AD/13H (MON part).
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (5) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-U ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check of the wiring of the DSI 43 signal from the ELAC1 (2CE1) COM part and the MON part to the ground terminal ASM 279240.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (4) Do a check for an open circuit of the wirings of the DSI 20, 39 and 47 signals from the ELAC1 (2CE1) COM part and the MON part ASM 279240:
  • For DSI 20: pin AA/5C (COM part) and pin AD/2G (MON part).
  • For DSI 39: pin AA/12J (COM part) and pin AD/15E (MON part).
  • For DSI 47: pin AA/5K (COM part) and pin AD/13H (MON part).
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (5) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-V ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check of the wiring of the DSI 47 signal from the ELAC1 (2CE1) COM part and the MON part to the ground terminal ASM 279240.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (4) Do a check for an open circuit of the wirings of the DSI 20, 22, 39 and 43 signals from the ELAC1 (2CE1) COM part and the MON part ASM 279240:
  • For DSI 20: pin AA/5C (COM part) and pin AD/2G (MON part).
  • For DSI 22: pin AB/1A (COM part) and pin AD/3E (MON part).
  • For DSI 39: pin AA/12J (COM part) and pin AD/15E (MON part).
  • For DSI 43: pin AB/6C (COM part) and pin AD/13G (MON part).
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (5) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-289-W ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Replace ELAC-1 [2CE1] AMM 27-93-34-000-001 and AMM 27-93-34-400-001.
   (2) If the fault continues:
  • Do a check of the wiring of the DGO 04 signal from the ELAC1 (2CE1) COM part to the MON part (DGI 01) and the MON part (DGO 04) to the COM part (DGI 01) ASM 279250.
  • If the wiring is not correct, repair the above wiring.
  • If the wiring is correct, continue the procedure.
   (3) Do a check for an open circuit of the wirings of the DSI 20, 39 and 47 signals from the ELAC1 (2CE1) COM part and the MON part ASM 279240:
  • For DSI 20: pin AA/5C (COM part) and pin AD/2G (MON part).
  • For DSI 39: pin AA/12J (COM part) and pin AD/15E (MON part).
  • For DSI 47: pin AA/5K (COM part) and pin AD/13H (MON part).
  • If the wirings are not correct, repair the above wirings.
  • If the wirings are correct, continue the procedure.
   (4) Do the trouble shooting procedure (Ref. TSM TASK 27-93-00-810-896).
Subtask 27-93-00-810-236-A ** ON A/C NOT FOR ALL
DELETED
Subtask 27-93-00-810-236-C ** ON A/C NOT FOR ALL
DELETED
Subtask 27-93-00-810-236-F ** ON A/C NOT FOR ALL
DELETED
Subtask 27-93-00-810-236-L ** ON A/C NOT FOR ALL
DELETED
Subtask 27-93-00-810-236-N ** ON A/C NOT FOR ALL
DELETED
Subtask 27-93-00-740-201-A
C. Do the test given in Para. 3.
[Rev.8 from Aug 2018] 2026.04.04 04:28:08 UTC
"WTRUIB" 2025