Removal of the Thrust Reverser Half Door Stirrups [CFMB]

TASK 78-36-41-000-044-A
Removal of the Thrust Reverser Half Door Stirrups

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
Half Door Stirrups and Centering Pins

3. Job Set-up
Subtask 78-36-41-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 78-36-41-010-052-A ** ON A/C NOT FOR ALL

B. Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR

Subtask 78-36-41-040-051-A ** ON A/C NOT FOR ALL

C. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041).

Subtask 78-36-41-010-053-A ** ON A/C NOT FOR ALL

D. Open the left thrust reverser cowl door (Ref. AMM TASK 78-36-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
451AL
(2) FOR [1000EM2] (ENGINE-2)
461AL

4. Procedure
Subtask 78-36-41-020-051-A ** ON A/C NOT FOR ALL

A. Removal of the Thrust Reverser Half Door Stirrups:
(1) Removal of the Aft Half Door Stirrup
(a) Remove the screw (15) and locking bracket (10) from the tension nut (20).
(b) Remove the tension nut (20) from the stirrup (30).
(c) Remove the stirrup (30) from the thrust reverser half door.
(2) Removal of the Middle Half Door Stirrup
(a) Remove the screw (15) and locking bracket (10) from the tension nut (20).
(b) Remove the tension nut (20) from the stirrup (30).
(c) Remove the stirrup (30) from the thrust reverser half door.
(3) Removal of the Forward Half Door Stirrups
(a) Remove the screws (15) and locking brackets (10) from the tension nuts (20).
(b) Remove the tension nuts (20) from the stirrups (30).
(c) Remove the stirrups (30) from the thrust reverser half door.

[Rev.10 from 2021] 2026.04.01 13:12:03 UTC