Removal of the Thrust Reverser Half Door Latches [CFMB]

TASK 78-36-41-000-043-A
Removal of the Thrust Reverser Half Door Latches

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
Thrust Reverser Half Door Latches

3. Job Set-up
Subtask 78-36-41-941-050-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 78-36-41-010-050-A ** ON A/C NOT FOR ALL

B. Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR

Subtask 78-36-41-040-050-A ** ON A/C NOT FOR ALL

C. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041)

Subtask 78-36-41-010-051-A ** ON A/C NOT FOR ALL

D. Open the right thrust reverser door: (Ref. AMM TASK 78-36-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
452AR
(2) FOR [1000EM2] (ENGINE-2)
462AR

4. Procedure
Subtask 78-36-41-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the Thrust Half Door Latches:
(1) Removal of the Forward Half Door Latches
(a) Remove and discard the cotter pin (5).
(b) Remove the nut (10) and the bolt (20).
(c) Remove the latches (15) from the thrust reverser half door.
(2) Removal of the Middle Half Door Latch
(a) Remove and discard the cotter pin (5).
(b) Remove the nut (10) and the bolt (30).
(c) Remove the latch (25) from the thrust reverser half door.
(3) Removal of the Aft Half Door Latch
(a) Remove the bolt (30) and bracket (35).
(b) Remove the pin (40).
(c) Remove the latch (25) from the thrust reverser half door.

[Rev.10 from 2021] 2026.04.01 03:26:27 UTC