W DOC AIRBUS | AMM A320F

Manual Deployment of the Blocker Door [CFMI]


TASK 78-32-41-860-040-A
Manual Deployment of the Blocker Door


FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 1M(3 FT)
No specific
AR
WARNING NOTICE(S)
HIX3005
1
SAFETY SLEEVE - PIVOTING DOOR ACTUATOR
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 71-13-00-010-040-A
Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-A
Make the Thrust Reverser Unserviceable for Maintenance
3. Job Set-up
Subtask 78-32-41-941-068-A ** ON A/C NOT FOR ALL
A. Safety Precautions
   (1) On the center pedestal, on the ENG panel 115VU:
     (a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
   (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
   (3) On the overhead maintenance panel 50VU:
     (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
     (b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 78-32-41-010-080-A ** ON A/C NOT FOR ALL
B. Get Access
   (1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
     (a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
     (b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
   (2) Put the ACCESS PLATFORM 1M(3 FT) in position.
Subtask 78-32-41-040-074-A ** ON A/C NOT FOR ALL
C. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041).
4. Procedure
Subtask 78-32-41-860-059-B ** ON A/C NOT FOR ALL
A. Manual Deployment of the Blocker Door
   (1) Turn the Dzus fastener on the thermal blankets (30), (35) and (40) to loosen it and remove the blanket from the blocker door latch (15).
   (2) Turn the manual unlock shaft on the blocker door latch to the unlock position with a 5/16 in. (7.94 mm) wrench.
NOTE: The manual unlock shaft can be accessed through a slot on the right or left side of the blocker door latch.
   (3) Turn the manual unlock square on the hydraulic actuator to the unlock position.
NOTE: The blocker door automatically disengages from its hook.
   (4) Open the blocker door:
CAUTION: DO NOT PUSH ON THE STOW SWITCH LEVER WHEN BLOCKER DOOR IS OPENED OR DAMAGE COULD OCCUR.
     (a) Open the blocker door by manually pulling on its edge.
   (5) If maintenance has to be performed with the blocker door in the open position, remove the screw and the lock-out fairing on the blocker door and install the HIX3005 SAFETY SLEEVE - PIVOTING DOOR ACTUATOR on the blocker door actuator.
[Rev.10 from 2021] 2026.04.01 03:52:06 UTC