Removal of the P3/T3 Sensor [IAE]

TASK 73-22-15-000-010-A
Removal of the P3/T3 Sensor

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 400
FIN: 4024KS ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.V10-058)	Penetrating oil

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 462AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 78-30-00-040-012-A	Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-32-00-010-010-A	Opening of the Thrust Reverser Halves
P3/T3 Sensor

3. Job Set-up
Subtask 73-22-15-941-050-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 73-22-15-010-050-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowls (Ref. AMM TASK 71-13-00-010-010)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Put the ACCESS PLATFORM 1M(3 FT) in to position.

Subtask 73-22-15-040-050-A ** ON A/C NOT FOR ALL

C. Deactivate the thrust reverser.

WARNING: MAKE SURE THAT THE THRUST REVERSER HYDRAULIC CONTROL UNIT (HCU) IS DEACTIVATED BEFORE YOU DO WORK ON OR AROUND THE THRUST REVERSER. IF THE HCU IS NOT DEACTIVATED, THERE IS A RISK OF UNWANTED THRUST REVERSER OPERATION WHICH CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

(1) Deactivate the thrust reverser hydraulic control unit (HCU) (Ref. AMM TASK 78-30-00-040-012).

Subtask 73-22-15-010-051-A ** ON A/C NOT FOR ALL

D. Open the right thrust reverser halves (Ref. AMM TASK 78-32-00-010-010):
(1) FOR [1000EM1] (ENGINE-1)
452AR
(2) FOR [1000EM2] (ENGINE-2)
462AR

4. Procedure
Subtask 73-22-15-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the P3/T3 sensor:
(1) Disconnect the harness leads from the P3/T3 sensor (5).
(a) remove the two nuts (3) and the two nuts (4) from the four sensor terminals.
(b) Remove the four harness leads from the terminals.
(2) Disconnect the pressure tube (2) from the P3/T3 sensor.
(a) Remove the lockwire from the tube on the side of the sensor.
(b) Disconnect the pressure tube (2) from the sensor.
(3) Disconnect the P3/T3 sensor (5) from the diffuser case assembly.
(a) Remove the wire from the bolts (1) which hold the sensor (5) to the diffuser case assembly (7).
(b) Apply, Penetrating oil (Material No.V10-058) to the bolts.
Remove the bolts which hold the sensor to the diffuser case assembly.
(4) Remove the sensor from the diffuser case assembly:
(a) Remove the sensor from the diffuser case assembly.
(b) Remove the gasket (6) from the boss (8). Discard the gasket.

[Rev.10 from 2021] 2026.04.01 03:00:49 UTC