Removal of the Electronic Engine Control (EEC) Wiring Harness (WF06) [PW11]

TASK 73-21-66-000-802-A
Removal of the Electronic Engine Control (EEC) Wiring Harness (WF06)

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AND THE ADJACENT COMPONENTS AFTER ENGINE SHUTDOWN. THE ENGINE, THE ENGINE OIL AND THE ADJACENT COMPONENTS CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

CAUTION: DO NOT BEND OR TWIST THE HARNESS TOO MUCH. IF YOU DO, DAMAGE TO THE HARNESS CAN OCCUR.

FIN: 4089KS ** ON A/C NOT FOR ALL

1. Reason for the Job
Use this procedure to remove the harness (WF06).
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	COVER - PROTECTION
No specific	1	PLIERS - JAWED, SOFT
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-00-00-860-832-A	Procedure to Prevent Engine Motoring and to Stop the Electrical Supply to the EEC
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
EEC Wiring Harness WF06

3. Job Set-up
Subtask 73-21-66-941-054-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Do the procedure to prevent engine motoring and to stop the electrical supply to the Electronic Engine Control (EEC)
(Ref. AMM TASK 71-00-00-860-832).

Subtask 73-21-66-865-056-A ** ON A/C NOT FOR ALL

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
FOR FIN: 4020KM1 (POWER PLANTDEMOUNTABLE, ENG 1)
121VU	DCV A/ENG1 PWR SUPPLY	102KS1	K42
** ON A/C NOT FOR ALL
121VU	DCV A/ENG1 PWR SUPPLY	102KS1	N44
** ON A/C NOT FOR ALL
FOR FIN: 4020KM2 (POWER PLANTDEMOUNTABLE, ENG 2)
121VU	DCV A/ENG2 PWR SUPPLY	102KS2	K43
** ON A/C NOT FOR ALL
121VU	DCV A/ENG2 PWR SUPPLY	102KS2	N45

Subtask 73-21-66-010-054-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 73-21-66-020-052-A ** ON A/C NOT FOR ALL

A. Removal of the Electronic Engine Control (EEC) Wiring Harness WF06
(1) Find the EEC wiring harness (WF06) (1) attached to the right-hand side of the fan case, see the sheet 1 of the figure.
(2) Remove the harness (WF06) (1) from the engine as follows: see the sheet 1 throught 4 of the figure.
(a) Disconnect the harness (WF06) connectors from the engine with the PLIERS - JAWED, SOFT as follows:
1 Disconnect the connector (P7) from the EEC.
2 Disconnect the connector (P491) from the pylon.
(b) Remove the harness (WF06) (1) from the spring clips.
(c) Remove the harness (WF06) (1) from the engine.
(3) Installation of the protection covers

CAUTION: INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.

(a) Make sure that you install all the necessary COVER - PROTECTION to prevent engine damage.

[Rev.10 from 2021] 2026.04.01 03:03:11 UTC