Removal of the Data Storage Unit [PW11]

TASK 73-21-02-000-801-A
Removal of the Data Storage Unit

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AND THE ADJACENT COMPONENTS AFTER ENGINE SHUTDOWN. THE ENGINE, THE ENGINE OIL AND THE ADJACENT COMPONENTS CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

ZONE: 400
FIN: 4670KS ** ON A/C NOT FOR ALL

1. Reason for the Job
Use this procedure to remove the DSU.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M(3 FT)
No specific	1	CONTAINER - CLEAN, APPLICABLE
No specific	AR	COVER - PROTECTION
No specific	AR	PLIERS - JAWED, SOFT

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 31-32-00-860-012-A	Procedure to Get Access to the SYSTEM REPORT/TEST/ENG Page
TASK 71-00-00-860-832-A	Procedure to Prevent Engine Motoring and to Stop the Electrical Supply to the EEC
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
Data Storage Unit (DSU)

3. Job Set-up
Subtask 73-21-02-740-051-A ** ON A/C NOT FOR ALL

A. Print the Trouble Shooting Data
(1) On MCDU 1(2), get the SYSTEM REPORT/TEST ENG page (Ref. AMM TASK 31-32-00-860-012).
(2) Push the line key adjacent to the FADEC indication.
(3) Push the line key adjacent to the TROUBLESHOOT DATA indication.
(4) Print the troubleshooting data for each flight leg and ground leg.

Subtask 73-21-02-941-050-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) Do the procedure to prevent engine motoring and to stop the electrical supply to the Electronic Engine Control (EEC)
(Ref. AMM TASK 71-00-00-860-832)

Subtask 73-21-02-010-050-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position.

4. Procedure
Subtask 73-21-02-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the Data Storage Unit (DSU)

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

(1) Find the DSU (3) attached to the EEC at the 2 o'clock position on the fan case assembly.
(2) Remove the DSU (3) as follows:
(a) Remove the bolt (2) that attaches the DSU lanyard to the EEC support bracket.
(b) Use the PLIERS - JAWED, SOFT to disconnect the DSU (3) from the EEC.
(c) Put the DSU (3) in a suitable CONTAINER - CLEAN, APPLICABLE.
(3) Installation of protection covers

CAUTION: INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.

(a) Make sure that you install COVER - PROTECTION as necessary to prevent damage to the engine.

[Rev.10 from 2021] 2026.04.01 03:02:45 UTC