DOC AIRBUS | AMM A320FRepair of Fan Composite Outlet Guide Vane (OGV) [CFMI]
TASK 72-23-00-300-009-A
Repair of Fan Composite Outlet Guide Vane (OGV)
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Referenced Information
3. Job Set-up
Subtask 72-23-00-941-050-A ** ON A/C NOT FOR ALL
Subtask 72-23-00-310-051-A ** ON A/C NOT FOR ALL
Subtask 72-23-00-410-064-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 02:38:50 UTC
Repair of Fan Composite Outlet Guide Vane (OGV)
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CUTTER - THIN BLADE |
| No specific | AR | WARNING NOTICE(S) |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.CP1039) | acetone |
| (Material No.CP1041) | isopropyl alcohol |
| (Material No.CP2011) | stoddard solvent |
| (Material No.CP2515) | Speed Tape (aluminum) 3M ALY 434 |
| (Material No.CP2516) | Speed Tape (aluminum) 3M ALY 435 |
| (Material No.CP2559) | ardrox 552 |
| (Material No.CP2560) | turco ind 79 |
| (Material No.CP2566) | mag-chem teksol |
| (Material No.CP2584) | degreasol 99 R |
| (Material No.CP2656) | mag-chem skysol |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 72-21-00-000-001-A | Removal of the Spinner Front Cone |
| TASK 72-21-00-000-002-A | Removal of the Spinner Rear Cone |
| TASK 72-21-00-000-003-A | Removal of the Fan Rotor Blades |
| TASK 72-21-00-400-001-A | Installation of the Spinner Front Cone |
| TASK 72-21-00-400-002-A | Installation of the Spinner Rear Cone |
| TASK 72-21-00-400-003-A | Installation of the Fan Rotor Blades |
Repair of Composite Outlet Guide Vane (OGV)Subtask 72-23-00-941-050-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 72-23-00-010-064-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
B. Get Access
(1) Remove the spinner front cone (Ref. AMM TASK 72-21-00-000-001).
(2) Remove the spinner rear cone (Ref. AMM TASK 72-21-00-000-002).
(3) Remove the fan blades (Ref. AMM TASK 72-21-00-000-003).
4. Procedure(1) Remove the spinner front cone (Ref. AMM TASK 72-21-00-000-001).
(2) Remove the spinner rear cone (Ref. AMM TASK 72-21-00-000-002).
(3) Remove the fan blades (Ref. AMM TASK 72-21-00-000-003).
Subtask 72-23-00-310-051-A ** ON A/C NOT FOR ALL
A. Repair of Fan Composite Outlet Vane
(1) Use a CUTTER - THIN BLADE to remove polyurethane residues and loose fibers and obtain a smooth and continuous profile, without sharp edges.
(2) Cleaning of the leading edge:
(3) Cut off a length ofCP2515 Speed Tape (aluminum) 3M ALY 434 CP2516 Speed Tape (aluminum) 3M ALY 435
(4) Apply the speed tape symetricaly over the OGV leading edge. Make sure it bonds correctly to the leading edge concave and convex surface without wrinkling.
(5) Put hand pressure on the tape to complete the bonding.
5. Close-up(1) Use a CUTTER - THIN BLADE to remove polyurethane residues and loose fibers and obtain a smooth and continuous profile, without sharp edges.
(2) Cleaning of the leading edge:
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
(a) Clean the leading edge concave and convex sides of the composite OGV with acetone (Material No.CP1039) or isopropyl alcohol (Material No.CP1041) or stoddard solvent (Material No.CP2011) or ardrox 552 (Material No.CP2559) or turco ind 79 (Material No.CP2560) or mag-chem teksol (Material No.CP2566) or degreasol 99 R (Material No.CP2584) or mag-chem skysol (Material No.CP2656) . (3) Cut off a length of
(4) Apply the speed tape symetricaly over the OGV leading edge. Make sure it bonds correctly to the leading edge concave and convex surface without wrinkling.
(5) Put hand pressure on the tape to complete the bonding.
Subtask 72-23-00-410-064-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Install the fan blades (Ref. AMM TASK 72-21-00-400-003).
(2) Install the spinner rear cone (Ref. AMM TASK 72-21-00-400-002).
(3) Install the spinner front cone (Ref. AMM TASK 72-21-00-400-001).
(4) Make sure that the work area is clean and clear of tools and other items.
(5) Remove the WARNING NOTICE(S).
(1) Install the fan blades (Ref. AMM TASK 72-21-00-400-003).
(2) Install the spinner rear cone (Ref. AMM TASK 72-21-00-400-002).
(3) Install the spinner front cone (Ref. AMM TASK 72-21-00-400-001).
(4) Make sure that the work area is clean and clear of tools and other items.
(5) Remove the WARNING NOTICE(S).