Installation of the Reservoir To Manifold Oil Drain Tube [CFMI]

TASK 71-73-49-400-001-A
Installation of the Reservoir To Manifold Oil Drain Tube

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 250 and 200 lbf.in (2.83 and 2.26 m.daN )

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-A	Closing of the Fan Cowl Doors
Tubes - Oil, Hydraulic and Water Drain

3. Job Set-up
Subtask 71-73-49-860-075-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).

Subtask 71-73-49-010-114-A ** ON A/C NOT FOR ALL

B. Make sure that the fan cowl doors are open: (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR

4. Procedure
Subtask 71-73-49-420-082-A ** ON A/C NOT FOR ALL

A. Installation of the Reservoir-to-Manifold Oil Drain-Tube.
(1) Remove the protective covers from the manifold module, the drain reservoir, the tube (110), and the tube (120).
(2) Connect the reservoir to manifold oil drain tube (120) to drain reservoir. Do not torque the coupling at this time.
(3) Connect the reservoir to manifold oil drain tube (120) to the manifold module. Do not torque the coupling at this time.
(4) Connect the tube (110) to the reservoir to manifold oil drain tube (120). Do not torque the coupling at this time.
(5) Make sure that the reservoir to manifold oil drain tube (120) is aligned correctly on the engine.
(6) TORQUE the coupling on the tube (110) to between 250 and 200 lbf.in (2.83 and 2.26 m.daN )

.
(7) TORQUE the couplings on the two ends of the tube (120) to between 250 and 200 lbf.in (2.83 and 2.26 m.daN )

5. Close-up
Subtask 71-73-49-410-083-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors: (Ref. AMM TASK 71-13-00-410-040)
(3) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(4) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(5) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 02:24:09 UTC