DOC AIRBUS | AMM A320FRemoval of the Fan Case Drain Tube [CFMI]
TASK 71-73-49-000-041-A
Removal of the Fan Case Drain Tube
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 71-73-49-941-072-A ** ON A/C NOT FOR ALL
Subtask 71-73-49-020-072-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 12:55:09 UTC
Removal of the Fan Case Drain Tube
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CONTAINER 1 L (1/4 USGAL) |
| No specific | AR | COVER - PROTECTION |
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 438AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 448AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 71-13-00-010-040-A | Opening of the Fan Cowl Doors |
Tubes - Oil, Hydraulic and Water DrainSubtask 71-73-49-941-072-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 71-73-49-010-089-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
B. Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
4. Procedure(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
Subtask 71-73-49-020-072-A ** ON A/C NOT FOR ALL
A. Removal of the Fan Case Drain-Tube.
(1) Put a CONTAINER 1 L (1/4 USGAL) below the drain mast to catch any fluid remaining in the tubes.
(2) Remove the clamp (5), the screw (10), the washer (15), and the nut (20) that attach the fan case drain tube (35) to the oil tank drain tube (30).
(3) Disconnect the fan case drain tube (35) from the manifold module and allow the fluid to drain.
(4) Disconnect the fan case drain tube (35) from the engine tube.
(5) Remove the fan case drain tube (35) from the engine.
(6) Put COVER - PROTECTION on the manifold module, the engine tube, and the two ends of the drain tube (35).
(7) Remove the container from below the drain mast.
Subtask 71-73-49-020-072-B ** ON A/C NOT FOR ALL (1) Put a CONTAINER 1 L (1/4 USGAL) below the drain mast to catch any fluid remaining in the tubes.
(2) Remove the clamp (5), the screw (10), the washer (15), and the nut (20) that attach the fan case drain tube (35) to the oil tank drain tube (30).
(3) Disconnect the fan case drain tube (35) from the manifold module and allow the fluid to drain.
(4) Disconnect the fan case drain tube (35) from the engine tube.
(5) Remove the fan case drain tube (35) from the engine.
(6) Put COVER - PROTECTION on the manifold module, the engine tube, and the two ends of the drain tube (35).
(7) Remove the container from below the drain mast.
A. Removal of the Fan Case Drain-Tube
(1) Put a CONTAINER 1 L (1/4 USGAL) below the drain mast to catch any fluid remaining in the tubes.
(2) Remove the clamp (5), the bolt (12), and the nut (23) that attach the fan case drain tube (35) to the oil tank drain tube (30).
(3) Disconnect the fan case drain tube (35) from the manifold module and allow the fluid to drain.
(4) Disconnect the fan case drain tube (35) from the engine tube.
(5) Remove the fan case drain tube (35) from the engine.
(6) Put COVER - PROTECTION on the manifold module, the engine tube, and the two ends of the drain tube (35).
(7) Remove the container from below the drain mast.
(1) Put a CONTAINER 1 L (1/4 USGAL) below the drain mast to catch any fluid remaining in the tubes.
(2) Remove the clamp (5), the bolt (12), and the nut (23) that attach the fan case drain tube (35) to the oil tank drain tube (30).
(3) Disconnect the fan case drain tube (35) from the manifold module and allow the fluid to drain.
(4) Disconnect the fan case drain tube (35) from the engine tube.
(5) Remove the fan case drain tube (35) from the engine.
(6) Put COVER - PROTECTION on the manifold module, the engine tube, and the two ends of the drain tube (35).
(7) Remove the container from below the drain mast.