Installation of the Vibration Sensor Harness 238D0912 [CFMI]

TASK 71-51-44-400-006-A
Installation of the Vibration Sensor Harness 238D0912

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 22 and 20 lbf.in (0.25 and 0.23 m.daN )
No specific	Torque wrench: range to between 25 and 20 lbf.in (0.28 and 0.23 m.daN )

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 70-60-00-910-042-A	Nacelle Standard Practices
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-A	Closing of the Fan Cowl Doors
TASK 77-32-34-710-040-A	Operational Check of EVMU through CFDS for Advisory Indication on ECAM
Vibration Sensor Harness

3. Job Set-up
Subtask 71-51-44-860-055-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.

Subtask 71-51-44-010-061-A ** ON A/C NOT FOR ALL

B. Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR

Subtask 71-51-44-865-066-A ** ON A/C NOT FOR ALL

WARNING: OPEN THE PROBE HEATER CIRCUIT-BREAKERS 1DA1(2), 3DA1(2,3), 4DA1(2,3) AND 5DA1(2,3) BEFORE ENG1(2)FADEC A and EIU 1(2) C/B'S 2KS1 AND 2KS2. IF YOU DO NOT OBEY THIS SEQUENCE:

THE PROBES WILL BECOME TOO HOT.
THIS CAN CAUSE DAMAGE TO EQUIPMENT AND INJURY TO MAINTENANCE PERSONNEL.

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ENGINE/1 AND 2/IGN/SYS A	1JH	A03
49VU	ANTI ICE/PROBES/AOA/1	4DA1	D04
49VU	ANTI ICE/PROBES/PITOT/1	3DA1	D02
49VU	COM/CVR/SPLY	2RK	E14
49VU	COM/CVR/CTL	4RK	E13
121VU	RCDR/DFDR	7TU	K16
121VU	HYDRAULIC/HYD POWER/Y	3803GX	N30
122VU	ANTI ICE/WINDOWS/R	4DG2	W14
122VU	ANTI ICE/WINDOWS/L	4DG1	X14
122VU	ANTI ICE/PROBES/2/PITOT	3DA2	Y14
122VU	ANTI ICE/PROBES/2/AOA	4DA2	Y13
122VU	ANTI ICE/PROBES/2/STATIC	5DA2	Y11
122VU	ANTI ICE/PROBES/3/PITOT	3DA3	Z16
122VU	ANTI ICE/PROBES/3/AOA	4DA3	Z15
122VU	ANTI ICE/PROBES/3/STATIC	5DA3	Z14
122VU	ANTI ICE/PROBES/1/STATIC	5DA1	Z13
123VU	Y HYD/ELEC/PUMP	3802GX	AB06
123VU	Y HYD/ELEC/ELEC PUMP/NORM	3801GX	AB03
FOR FIN: 1000EM1 (ENGINE1)
49VU	ENGINE/1/FIRE DET/LOOP A	7WD1	A06
49VU	ENGINE/1/FADEC A/AND EIU 1	2KS1	A04
121VU	ENGINE/IGN/ENG1/SYS B	3JH1	P41
121VU	ENGINE/IGN/ENG1/SYS A BAT	2JH1	P39
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL1/SQUIB/B	2WE1	Q44
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL1/SQUIB/A	1WE1	Q43
121VU	ENGINE/ENG1/FIRE DET/LOOP B	8WD1	Q38
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R41
122VU	ELEC/GCU/1	2XU1	T26
FOR FIN: 1000EM2 (ENGINE2)
49VU	ENGINE/2/FIRE DET/LOOP B	8WD2	A07
49VU	ENGINE/2/FADEC A/AND EIU 2	2KS2	A05
121VU	ENGINE/IGN/ENG2/SYS B	3JH2	P42
121VU	ENGINE/IGN/ENG2/SYS A BAT	2JH2	P40
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL2/SQUIB/B	2WE2	Q42
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL2/SQUIB/A	1WE2	Q41
121VU	ENGINE/ENG2/FADEC B	4KS2	Q40
121VU	ENGINE/ENG2/FIRE DET/LOOP A	7WD2	Q39
122VU	ELEC/GCU/2	2XU2	T27

4. Procedure
Subtask 71-51-44-420-055-A ** ON A/C NOT FOR ALL

A. Installation of the Vibration Sensor Harness 238D0912

NOTE: Refer to the recommended procedure for the installation of the wire harness (Ref. AMM TASK 70-60-00-910-042).

(1) Remove the protective covers from the electrical connectors.
(2) Put the electrical harness (5) in position on the engine.
(3) Connect the electrical connector 448VC-A to the pylon junction box. Tighten the connector with your hand plus one-eighth turn.
(4) Put the clamps (25) and (35) on the upper section of the harness (5). Make sure that the other clamps are installed correctly.

NOTE: Detail A shows the most current harness installation. Detail B illustrates the initial harness installation. Refer to the illustrated parts catalog for applicable harness installation configurations.

(5) Attach the clamps (25) and (40) together with the screw (30), the washers (15) and (45) and the nut (20).
(6) Attach the clamp (25) to the bracket with the screw (10), the washer (15) and the nut (20).
(7) Attach the clamps (25) to the brackets with the screws (10) and the washers (15).
(8) Attach the clamps (35) together with the screw (30), the washer (15) and the nut (20).
(9) Attach the clamps (25) and (40) together with the screw (30), the washer (15) and the nut (20).
(10) Put the clamps (25) on the lower section of the harness (5). Make sure that clamps (50) are installed on the thrust reverser harness.
(11) Attach the clamps (25) to the brackets with the screws (10), the washers (15) and the nuts (20).
(12) Attach the clamps (25) and (50) to the brackets with the screws (30), the washers (15) and (45).
(13) TORQUE the screws (10) and (30) to between 22 and 20 lbf.in (0.25 and 0.23 m.daN )

.
(14) TORQUE the nuts (20) to between 25 and 20 lbf.in (0.28 and 0.23 m.daN )

.
(15) Connect electrical connector 4002EV-A to the No.1 bearing vibration accelerometer. Tighten the connector with you hand plus one-eighth turn.
(16) Examine the harness installation and make sure that all clamps are installed correctly.

Subtask 71-51-44-865-067-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ENGINE/1 AND 2/IGN/SYS A	1JH	A03
49VU	ANTI ICE/PROBES/AOA/1	4DA1	D04
49VU	ANTI ICE/PROBES/PITOT/1	3DA1	D02
49VU	COM/CVR/SPLY	2RK	E14
49VU	COM/CVR/CTL	4RK	E13
121VU	RCDR/DFDR	7TU	K16
121VU	HYDRAULIC/HYD POWER/Y	3803GX	N30
122VU	ANTI ICE/WINDOWS/R	4DG2	W14
122VU	ANTI ICE/WINDOWS/L	4DG1	X14
122VU	ANTI ICE/PROBES/2/PITOT	3DA2	Y14
122VU	ANTI ICE/PROBES/2/AOA	4DA2	Y13
122VU	ANTI ICE/PROBES/2/STATIC	5DA2	Y11
122VU	ANTI ICE/PROBES/3/PITOT	3DA3	Z16
122VU	ANTI ICE/PROBES/3/AOA	4DA3	Z15
122VU	ANTI ICE/PROBES/3/STATIC	5DA3	Z14
122VU	ANTI ICE/PROBES/1/STATIC	5DA1	Z13
123VU	Y HYD/ELEC/PUMP	3802GX	AB06
123VU	Y HYD/ELEC/ELEC PUMP/NORM	3801GX	AB03
FOR FIN: 1000EM1 (ENGINE1)
49VU	ENGINE/1/FIRE DET/LOOP A	7WD1	A06
49VU	ENGINE/1/FADEC A/AND EIU 1	2KS1	A04
121VU	ENGINE/IGN/ENG1/SYS B	3JH1	P41
121VU	ENGINE/IGN/ENG1/SYS A BAT	2JH1	P39
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL1/SQUIB/B	2WE1	Q44
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL1/SQUIB/A	1WE1	Q43
121VU	ENGINE/ENG1/FIRE DET/LOOP B	8WD1	Q38
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R41
122VU	ELEC/GCU/1	2XU1	T26
FOR FIN: 1000EM2 (ENGINE2)
49VU	ENGINE/2/FIRE DET/LOOP B	8WD2	A07
49VU	ENGINE/2/FADEC A/AND EIU 2	2KS2	A05
121VU	ENGINE/IGN/ENG2/SYS B	3JH2	P42
121VU	ENGINE/IGN/ENG2/SYS A BAT	2JH2	P40
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL2/SQUIB/B	2WE2	Q42
121VU	ENGINE/ENG1 AND 2 FIRE EXTIG/BTL2/SQUIB/A	1WE2	Q41
121VU	ENGINE/ENG2/FADEC B	4KS2	Q40
121VU	ENGINE/ENG2/FIRE DET/LOOP A	7WD2	Q39
122VU	ELEC/GCU/2	2XU2	T27

Subtask 71-51-44-710-054-A ** ON A/C NOT FOR ALL

C. Do a test of the EVMU (Ref. AMM TASK 77-32-34-710-040).

5. Close-up
Subtask 71-51-44-410-055-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(3) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(4) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(5) Remove the access platform(s).
(6) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 12:55:05 UTC