Installation of the Fan Cowl Latch Proximity Sensor Harness [PW11]

TASK 71-13-61-400-801-A
Installation of the Fan Cowl Latch Proximity Sensor Harness

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: WEAR APPLICABLE PERSONAL PROTECTIVE EQUIPMENT (PPE) WHEN YOU DO THIS TASK. BEFORE YOU USE PPE, READ, UNDERSTAND AND OBEY ALL INSTRUCTIONS FOR ITS USE. THESE INSTRUCTIONS INCLUDE INSTRUCTIONS FROM THE MANUFACTURER, YOUR EMPLOYER AND GOVERNMENT REGULATIONS. YOU CAN GET INJURED IF YOU DO NOT USE PPE. GET INSTRUCTIONS FROM YOUR EMPLOYER ON WHICH PPE IS NECESSARY.

ZONE: 400
FIN: 4146KS ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	1	PLIERS - JAWED, SOFT
No specific	Torque wrench: range to between 27 and 24 lbf.in (0.31 and 0.27 m.daN )
No specific	Torque wrench: range to between 35 and 31.5 lbf.in (0.40 and 0.36 m.daN )

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-00-00-860-833-A	Procedure to Prevent Engine Motoring
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-802-A	Closing of the Fan Cowl Doors
TASK 71-13-00-710-802-A	Operational test of the Fan Cowl Loss Prevention System
Fan Cowl Latch Proximity Sensor Harness

3. Job Set-up
Subtask 71-13-61-941-051-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Make sure that you did the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).

Subtask 71-13-61-010-051-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR.
(2) Make sure that the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE is in position.

Subtask 71-13-61-865-051-A ** ON A/C NOT FOR ALL

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	ENGINE/LATCH DOORS & SLATS/ENG2	93KS2	P40
121VU	ENGINE/LATCH DOORS & SLATS/ENG1	93KS1	P39

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 71-13-61-420-050-A ** ON A/C NOT FOR ALL

A. Installation of the Fan Cowl Latch Proximity Sensor Harness
(1) Removal of protection covers

CAUTION: REMOVE THE PROTECTION COVERS FROM THE OPENINGS AS NECESSARY TO PREVENT ENGINE DAMAGE.

(a) Make sure that you remove all the necessary COVER - PROTECTION to prevent damage to the engine.

CONFIGURATION 1

(2) Install the fan cowl latch proximity sensor harness (3).
(a) Attach the proximity sensor harness (3) connector (4056VC) to the disconnect bracket with the four screws (2) and four washers (1).
(b) Tighten the screws (2) by hand.
(c) Connect the proximity sensor harness (3) connectors (4233KS-A), (4232KS-A) and (4231KS-A) to the proximity sensors on the fan cowl latches.
(d) Turn the proximity sensor harness (3) connectors (4233KS-A), (4232KS-A) and (4231KS-A) finger-tight. Turn the connectors 1/4 turn more with PLIERS - JAWED, SOFT.
(e) Put the 16 clamps (4) and clamp (6) on the proximity sensor harness (3).
(f) Install the 16 clamps (4) and proximity sensor harness (3) on the fan cowl door with the 16 bolts (5).
1 Do not torque the bolts (5) at this time.
(g) Install the clamp (6) and the proximity sensor harness (3) on the fan cowl door with the bolt (5).
1 Do not torque the bolt (5) at this time.
(h) Adjust the proximity sensor harness (3) to keep preload to a minimum. Make sure there are no kinks in the proximity sensor harness (3).
(i) TORQUE the bolts (5) to between 35 and 31.5 lbf.in (0.40 and 0.36 m.daN )

.
(k) Connect the pylon harness connector (4056VC-A) to the proximity sensor harness (7) connector (4056VC).
(l) Turn the pylon harness connector (4056VC-A) finger-tight. Turn the connector 1/4 turn more with PLIERS - JAWED, SOFT.

5. Close-up
Subtask 71-13-61-410-050-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).

Subtask 71-13-61-865-052-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	ENGINE/LATCH DOORS & SLATS/ENG2	93KS2	P40
121VU	ENGINE/LATCH DOORS & SLATS/ENG1	93KS1	P39

Subtask 71-13-61-710-050-A ** ON A/C NOT FOR ALL

C. Test(s)
(1) Do the Operational Test of the Fan Cowl Loss Prevention System Proximity Sensors (Ref. AMM TASK 71-13-00-710-802).

[Rev.10 from 2021] 2026.04.01 02:32:52 UTC