W DOC AIRBUS | AMM A320F

Installation of the Bearings of the Pylon Aft Attachment at RIB10

TASK 54-51-17-400-809-A
Installation of the Bearings of the Pylon Aft Attachment at RIB10

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION: BEFORE YOU INSTALL/REMOVE THE GSE-TOOL, READ THE INSTRUCTIONS IN THE APPLICABLE GSE INSTRUCTION MANUAL. WHILE YOU OPERATE THIS TOOL, CAREFULLY OBEY THEM. IF YOU DO NOT OBEY THE INSTRUCTIONS, DAMAGE TO EQUIPMENT CAN OCCUR.
ZONE: 470
ZONE: 480
FIN: 4020KM1
FIN: 4020KM2
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific
AR
SPATULA - PLASTIC
No specific
AR
WARNING NOTICE(S)
No specific
Torque wrench: range to between 28 and 22 m.daN (206.49 and 162.24 lbf.ft ) T
98D54003018000
1
BEARING RIB10 RI KIT
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
470
ENGINE 1 AFT PYLON
480
ENGINE 2 AFT PYLON
 D. Referenced Information
REFERENCE
DESIGNATION
TASK 54-51-17-400-808-A
Installation of the Pylon-to-Wing Aft Attach-Fittings at RIB10
TASK 78-30-00-440-807-A
Reactivation of the Thrust Reverser System after Nacelle Maintenance (ICU)
F Bearings of the Pylon Aft Attachment at RIB10
3. Job Set-up
Subtask 54-51-17-941-078-A
A. Safety Precautions
   (1) On the center pedestal, on ENG panel 115VU:
     (a) Make sure that the ENG/MODE selector switch is in the NORM position.
     (b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
     (c) Make sure that the WARNING NOTICE(S) is in position to tell persons not to operate the ENG/MODE selector switch and the ENG/MASTER 1(2) control switch.
   (2) On the ENG section of maintenance panel 50VU:
     (a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
     (b) Make sure that the WARNING NOTICE(S) is in position to tell persons not to energize FADEC 1(2).
   (3) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position:
     (a) For the left pylon, in zone 470
     (b) For the right pylon, in zone 480.
Subtask 54-51-17-110-058-A
B. Preparation for Installation
F Bearings of the Pylon Aft Attachment at RIB10
   (1) Clean the parts retained from the removed component with Non Aqueous Cleaner-General - - (Material No.08BAA9) and Textile-Lint free Cotton - (Material No.14SBA1) .
   (2) Use a SPATULA - PLASTIC to remove unwanted material from the interface of the pylon rear attachment.
   (3) Clean the interface of the bearings (4) and the pylon aft attachment (3) with Non Aqueous Cleaner-General - - (Material No.08BAA9) and Textile-Lint free Cotton - (Material No.14SBA1) , if necessary.
   (4) Examine the pylon aft attachment and the adjacent structure for:
  • Cracks
  • Damaged paint and sealant
  • Distortion
  • Correct condition of all the fasteners and safety devices.
4. Procedure
Subtask 54-51-17-420-098-A
A. Installation of the Bearings of the Pylon Aft Attachment at RIB10
F Bearings of the Pylon Aft Attachment at RIB10
   (1) Install new bearings (4) on the pylon aft attachment (3) with the 98D54003018000 BEARING RIB10 RI KIT.
   (2) Install new tab washers (2). Make sure that the internal tab of the washers (2) is engaged in the slot on the bearings (4).
NOTE: It is necessary to bend the tabs of the tab washers (2) before you install the slotted nuts (1). This will make it easier to bend the tabs when you subsequently lock the slotted nuts.
   (3) Install the slotted nuts (1) on the bearings (4) with the chamfered face against the tab washers (2).
   (4) Hold the bearings (4) with the 98D54003018000 BEARING RIB10 RI KIT.
   (5) TORQUE the slotted nuts (1) to between 28 and 22 m.daN (206.49 and 162.24 lbf.ft ) T with the 98D54003018000 BEARING RIB10 RI KIT.
   (6) Safety the slotted nuts (1) with the tab washers (2).
5. Close-up
Subtask 54-51-17-410-067-A
A. Close Access
   (1) Install the pylon-to-wing aft attach-fittings at RIB10 (Ref. AMM TASK 54-51-17-400-808).
Subtask 54-51-17-440-060-A
B. Reactivation of the Thrust Reverser
   (1) Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-440-807).
Subtask 54-51-17-942-069-A
C. Aircraft Maintenance Configuration
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Remove the access platform(s).
   (3) Remove the WARNING NOTICE(S).
[Rev.10 from 2021] 2026.04.01 12:50:15 UTC
"Aviabrain" 2025