Load Adjustment of the Control Handle of the AFT Passenger/Crew Door

TASK 52-13-00-820-002-A-01
Load Adjustment of the Control Handle of the AFT Passenger/Crew Door

1. Reason for the Job
This procedure is applicable with the escape slide or escape slide/raft installed.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific	AR	DYNAMOMETER 20 DAN (45 LBF) - PULL
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.14QFB1)	Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -

C. Referenced Information

REFERENCE	DESIGNATION
TASK 52-10-00-010-001-A	Opening of the Passenger/Crew Door
TASK 52-10-00-410-001-A	Closing of the Passenger/Crew Door
TASK 52-10-00-860-001-A	Special Precautions before Work on the Passenger/Crew Door
TASK 52-10-00-860-002-A	Special Precautions after Work on the Passenger/Crew Door
Load Adjustment of the Control Handle of the AFT Passenger/Crew Door ** ON A/C NOT FOR ALL
Load Adjustment of the Control Handle of the AFT Passenger/Crew Door ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 52-13-00-941-060-A

A. Get Access

WARNING: DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE THAN 65 KNOTS.

WARNING: BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:

THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.

IF YOU DO NOT OBEY THESE INSTRUCTIONS, THE DOOR CAN OPEN WITH FORCE OR THE ESCAPE SLIDE CAN DEPLOY SUDDENLY. THIS CAN CAUSE INJURY AND/OR DAMAGE.

WARNING: STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES. IF THE RED WARNING LIGHT FLASHES, REMAINING PRESSURE CAN CAUSE THE DOOR TO OPEN SUDDENLY AND CAN:

KILL OR CAUSE SERIOUS INJURY TO PERSONS
CAUSE DAMAGE TO THE AIRCRAFT.

(1) Put an ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in front of the passenger/crew door 832 or 842.
(2) Open the applicable passenger/crew door (Ref. AMM TASK 52-10-00-010-001).
(3) Obey the special precautions before you start work on the door (Ref. AMM TASK 52-10-00-860-001).

Subtask 52-13-00-865-057-A

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

4. Procedure
Subtask 52-13-00-820-067-A

A. Load Adjustment of the Control Handle

Load Adjustment of the Control Handle of the AFT Passenger/Crew Door ** ON A/C NOT FOR ALL

(1) Take a DYNAMOMETER 20 DAN (45 LBF) - PULL.
(2) Make sure that the load necessary to open the door with the inner control handle (2) is less than or equal to 18 daN (40.47 lbf).
(3) If the load is not in the tolerances, adjust as follows:
(a) Open the door.

WARNING: USE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(b) Remove and discard the lockwire from the tension bolt (1).
(c) Adjust the tension bolt (1) to get the correct load.
(d) Safety the tension bolt (1) with 14QFB1Wire-Locking Dia: 0.8 mm CRES Nickel Alloy -.
(4) Close the door and measure the load necessary to open the door with the inner control handle (2). If the load is not in the tolerances, do the adjustment again.
(5) Make sure that the inner control handle (2) comes back to its initial position with the door in the up position and the down position.

5. Close-up
Subtask 52-13-00-865-058-A

A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	EIS/SLIDES/ARM AND WARN/FLT	15WN	P11
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

Subtask 52-13-00-942-063-A

B. Close Access
(1) Obey the special precautions after the work on the door (Ref. AMM TASK 52-10-00-860-002).
(2) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(3) Close the applicable passenger/crew door 832 or 842 (Ref. AMM TASK 52-10-00-410-001).
(4) Remove the access platform(s).
(5) Make sure that the work area is clean and clear of tools and other items.

[Rev.10 from 2021] 2026.04.01 01:37:05 UTC