DOC AIRBUS | AMM A320FRemoval of the Photoluminescent Strip of the Floor-Proximity Emergency-Escape Path-Marking
TASK 33-51-21-000-001-A
Removal of the Photoluminescent Strip of the Floor-Proximity Emergency-Escape Path-Marking
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 33-51-21-860-050-A ** ON A/C NOT FOR ALL 4. Procedure
Subtask 33-51-21-020-050-I ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 12:34:13 UTC
Removal of the Photoluminescent Strip of the Floor-Proximity Emergency-Escape Path-Marking
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | SCRAPER - NON METALLIC |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
Subtask 33-51-21-860-050-A ** ON A/C NOT FOR ALL 4. Procedure
Subtask 33-51-21-020-050-I ** ON A/C NOT FOR ALL
A. Removal of the Photoluminescent Strip of the Floor-Proximity Emergency-Escape Path-Marking
Photoluminescent Strip (Floor Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
(1) Remove the carpet protector (7) from the photoluminescent strip (1).
(2) Remove the sealant (2) from the area that is between the non-textile floor covering and the photoluminescent strip (1) with the SCRAPER - NON METALLIC.
(3) Remove the photoluminescent strip (1) together with the adhesive tape (3) and the end-cap (6) (if installed) from the floor panels.
(4) Use the SCRAPER - NON METALLIC for the removal procedure.
(5) If necessary, remove the sealant from the end-cap (6) with the SCRAPER - NON METALLIC.
(6) Remove the end-cap (6) from the photoluminescent strip (1).
Subtask 33-51-21-020-050-AK ** ON A/C NOT FOR ALL Photoluminescent Strip (Floor Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL (2) Remove the sealant (2) from the area that is between the non-textile floor covering and the photoluminescent strip (1) with the SCRAPER - NON METALLIC.
(3) Remove the photoluminescent strip (1) together with the adhesive tape (3) and the end-cap (6) (if installed) from the floor panels.
(4) Use the SCRAPER - NON METALLIC for the removal procedure.
(5) If necessary, remove the sealant from the end-cap (6) with the SCRAPER - NON METALLIC.
(6) Remove the end-cap (6) from the photoluminescent strip (1).
A. Removal of the Photoluminescent Strip of the Floor-Proximity Emergency-Escape Path-Marking
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
(1) You must use a SCRAPER - NON METALLIC to help the removal procedure.
(2) Remove the clip (1) from the photoluminescent strips (2).
(3) Remove the sealant (4) between the non-textile floor covering and the photoluminescent strips (2) with a SCRAPER - NON METALLIC.
(4) Remove the photoluminescent strips (2).
(5) Remove the filler (3), if necessary.
Subtask 33-51-21-020-050-AV ** ON A/C NOT FOR ALL Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL (2) Remove the clip (1) from the photoluminescent strips (2).
(3) Remove the sealant (4) between the non-textile floor covering and the photoluminescent strips (2) with a SCRAPER - NON METALLIC.
(4) Remove the photoluminescent strips (2).
(5) Remove the filler (3), if necessary.
A. Removal of the Photoluminescent Strips of the Floor-Proximity Emergency-Escape Path-Marking
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
(1) Remove the photoluminescent strips (3) and (5) as follows:
(a) If necessary, remove the sealant from the end-cap clips (4) and the end-caps (7) with the SCRAPER - NON METALLIC.
(b) Remove the end-cap clips (4) and the end-caps (7).
(c) Remove the clips (1) from the photoluminescent strip (3).
(d) Remove the sealant (6) from the area that is between the non-textile floor covering and the photoluminescent strip (5) with the SCRAPER - NON METALLIC.
(e) Remove the filter films (2) from the photoluminescent strip (3).
(f) Remove the photoluminescent strips (3) and (5).
Subtask 33-51-21-020-050-AZ ** ON A/C NOT FOR ALL Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL (a) If necessary, remove the sealant from the end-cap clips (4) and the end-caps (7) with the SCRAPER - NON METALLIC.
(b) Remove the end-cap clips (4) and the end-caps (7).
(c) Remove the clips (1) from the photoluminescent strip (3).
(d) Remove the sealant (6) from the area that is between the non-textile floor covering and the photoluminescent strip (5) with the SCRAPER - NON METALLIC.
(e) Remove the filter films (2) from the photoluminescent strip (3).
(f) Remove the photoluminescent strips (3) and (5).
A. Removal of the Photoluminescent Strips of the Floor-Proximity Emergency-Escape Path-Marking
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
(1) Remove the photoluminescent strips (2) and (5) as follows:
(a) If necessary, remove the sealant from the end-cap clips (3) and the end-caps (7) with the SCRAPER - NON METALLIC.
(b) Remove the end-cap clips (3) and the end-caps (7).
(c) Remove the clips (1) from the photoluminescent strip (2).
(d) Remove the sealant (6) from the area that is between the non-textile floor covering and the photoluminescent strips (2) and (5) with the SCRAPER - NON METALLIC.
(e) Remove the photoluminescent strips (2) and (5).
(2) If necessary, remove the filler (4).
Subtask 33-51-21-020-050-BB ** ON A/C NOT FOR ALL Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL (a) If necessary, remove the sealant from the end-cap clips (3) and the end-caps (7) with the SCRAPER - NON METALLIC.
(b) Remove the end-cap clips (3) and the end-caps (7).
(c) Remove the clips (1) from the photoluminescent strip (2).
(d) Remove the sealant (6) from the area that is between the non-textile floor covering and the photoluminescent strips (2) and (5) with the SCRAPER - NON METALLIC.
(e) Remove the photoluminescent strips (2) and (5).
(2) If necessary, remove the filler (4).
A. Removal of the Photoluminescent Strip of the Floor-Proximity Emergency-Escape Path-Marking
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
Photoluminiscent Strip (Floor Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
(1) Remove the sealant (2) between the floor covering and the photoluminescent strip (1) with a SCRAPER - NON METALLIC.
(2) Remove the photoluminescent strip (1) from the floor panels. Use a SCRAPER - NON METALLIC to help the removal procedure.
(3) Remove the filler (3) together with the photoluminescent strip (1), if installed.
Subtask 33-51-21-020-050-BC ** ON A/C NOT FOR ALL Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL Photoluminiscent Strip (Floor Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL (2) Remove the photoluminescent strip (1) from the floor panels. Use a SCRAPER - NON METALLIC to help the removal procedure.
(3) Remove the filler (3) together with the photoluminescent strip (1), if installed.
A. Removal of the Photoluminescent Strip of the Floor-Proximity Emergency-Escape Path-Marking
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL
(a) If necessary, remove the sealant from the end-cap clips (5) with the SCRAPER - NON METALLIC.
(b) Remove the end-cap clips (5).
(c) Remove the clips (1) from the photoluminescent strip (3).
(d) Remove the sealant (6) from the area that is between the non-textile floor covering and the photoluminescent strip (3) with the SCRAPER - NON METALLIC.
(e) Remove the filter films (2) (if installed).
(f) Remove the photoluminescent strip (3).
(2) If necessary, remove the filler (4).
Photoluminescent Strip (Floor-Mounted) of the Floor-Proximity Emergency-Escape Path-Marking ** ON A/C NOT FOR ALL NOTE: You can use the SCRAPER - NON METALLIC for the removal procedure.
(1) Remove the photoluminescent strip (3) as follows: (a) If necessary, remove the sealant from the end-cap clips (5) with the SCRAPER - NON METALLIC.
(b) Remove the end-cap clips (5).
(c) Remove the clips (1) from the photoluminescent strip (3).
(d) Remove the sealant (6) from the area that is between the non-textile floor covering and the photoluminescent strip (3) with the SCRAPER - NON METALLIC.
(e) Remove the filter films (2) (if installed).
(f) Remove the photoluminescent strip (3).
(2) If necessary, remove the filler (4).