DOC AIRBUS | AMM A320FRemoval of the Temperature Sensor
TASK 30-73-18-000-002-A
Removal of the Temperature Sensor
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 30-73-18-861-052-A ** ON A/C NOT FOR ALL Subtask 30-73-18-865-053-A ** ON A/C NOT FOR ALL
Subtask 30-73-18-020-051-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 08:24:57 UTC
Removal of the Temperature Sensor
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 2M (6 FT) |
| No specific | AR | CAP - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 121 | AVIONICS COMPARTMENT |
| 131GW, 825 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
Temperature SensorSubtask 30-73-18-861-052-A ** ON A/C NOT FOR ALL Subtask 30-73-18-865-053-A ** ON A/C NOT FOR ALL
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 30-73-18-010-054-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | POT/WASTE WIP-HEATER-LINE | 1DW | A02 |
| 2000VU | POT/WASTE WIP-HEATER-CTL | 2DW | A01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | POT WIP-HEATER-LINE | 1DW | A02 |
| 2000VU | POT WIP-HEATER-CTL | 2DW | A01 |
C. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) at the FWD cargo-compartment door 825.
(2) Open the FWD cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).
(3) Set the CARGO COMPT LIGHT switch 6LU to ON.
(4) In the FWD cargo compartment, remove the sidewall panel 131GW.
4. Procedure(1) Put the ACCESS PLATFORM 2M (6 FT) at the FWD cargo-compartment door 825.
(2) Open the FWD cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).
(3) Set the CARGO COMPT LIGHT switch 6LU to ON.
(4) In the FWD cargo compartment, remove the sidewall panel 131GW.
Subtask 30-73-18-020-051-A ** ON A/C NOT FOR ALL
A. Removal of the Sensor
(1) Cut and discard the cable ties of the identification and warning labels.
(2) Remove the velcro tape (6) that attaches the sleeve (1) around the sensor.
(3) Remove the sleeve (1) from around the clamp sensor assembly (2) and the clamp (3).
(4) Disconnect the two wires of the clamp sensor assembly (2) from the terminal strip.
(5) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(6) On the potable water pipe remove the screws (4) and (5) from the clamp sensor assembly (2) and the clamp (3).
(7) Remove the clamp (3).
(8) Remove the clamp sensor assembly (2).
(1) Cut and discard the cable ties of the identification and warning labels.
(2) Remove the velcro tape (6) that attaches the sleeve (1) around the sensor.
(3) Remove the sleeve (1) from around the clamp sensor assembly (2) and the clamp (3).
(4) Disconnect the two wires of the clamp sensor assembly (2) from the terminal strip.
(5) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(6) On the potable water pipe remove the screws (4) and (5) from the clamp sensor assembly (2) and the clamp (3).
(7) Remove the clamp (3).
(8) Remove the clamp sensor assembly (2).