W DOC AIRBUS | AMM A320F

Removal of the Oven(s)

TASK 25-35-19-000-001-A
Removal of the Oven(s)

WARNING: BE CAREFUL WHEN YOU REMOVE OR INSTALL THIS EQUIPMENT. THIS EQUIPMENT IS HEAVY (MORE THAN 12 KG (26.5 lb)) AND CAN CAUSE INJURY AND/OR DAMAGE.
ZONE: 200
1. Reason for the Job
Self Explanatory
NOTE: More than one person is necessary for this procedure.
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
CAP - BLANKING
No specific
1
SCRAPER - NON METALLIC
FOR [6482MM] (GALLEY LOC.IV A/B)
No specific
AR
SCRAPER - NON METALLIC
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
200
UPPER HALF FUSELAGE
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 24-42-00-861-001-A
Energize the Ground Service Network from the External Power
F Oven ** ON A/C NOT FOR ALL
F Oven ** ON A/C NOT FOR ALL
F Oven ** ON A/C NOT FOR ALL
F Oven ** ON A/C NOT FOR ALL
F Oven(s) ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 25-35-19-861-058-A ** ON A/C NOT FOR ALL
A. Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
Subtask 25-35-19-860-063-A ** ON A/C NOT FOR ALL
B. At the applicable galley, on the galley control panel, open, safety and tag the circuit breaker(s) of the oven(s).
Subtask 25-35-19-860-050-A ** ON A/C NOT FOR ALL
C. Aircraft Maintenance Configuration
   (1) Make sure that the oven(s) is (are) empty.
Subtask 25-35-19-010-051-E ** ON A/C NOT FOR ALL
D. Get Access
   (1) Open all applicable doors to get access to the parts that you must remove/disconnect.
   (2) If necessary, remove the trolley(s).
   (3) If necessary, pull the table(s) out.
Subtask 25-35-19-010-051-G ** ON A/C NOT FOR ALL
D. Get Access
   (1) If necessary, remove the trolley(s).
Subtask 25-35-19-010-051-KG ** ON A/C NOT FOR ALL
D. Get Access
   (1) If necessary, remove the trolley(s).
   (2) If necessary, pull the table(s) out.
4. Procedure
Subtask 25-35-19-020-050-A ** ON A/C NOT FOR ALL
A. Removal of the Oven
F Oven ** ON A/C NOT FOR ALL
F Oven ** ON A/C NOT FOR ALL
WARNING: SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
   (1) Prevent damage to the component interfaces and the adjacent area.
   (2) Remove the screws (1).
   (3) Carefully pull the oven (2) out of the galley to disconnect the electrical connector.
   (4) Remove the oven (2) from the mounting rails (3).
   (5) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
Subtask 25-35-19-020-050-D ** ON A/C NOT FOR ALL
A. Removal of the Oven
F Oven ** ON A/C NOT FOR ALL
WARNING: SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
   (1) Remove the screws (1).
   (2) Carefully pull the oven (2) out of the mounting rails (3) to disconnect the electrical connector.
   (3) Remove the oven (2) from the galley.
   (4) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
Subtask 25-35-19-020-050-AC ** ON A/C NOT FOR ALL
A. Removal of the Oven
F Oven ** ON A/C NOT FOR ALL
WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
WARNING: SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
   (1) Remove the oven from the forward galley:
     (a) Remove the remaining sealant with a SCRAPER - NON METALLIC.
     (b) Remove the screws (6) and the washers (4).
     (c) Remove the filler (2).
     (d) Carefully pull the oven (7) out of the mounting rails (1) and disconnect the electrical connector.
     (e) Remove the oven (7) from the galley.
     (f) Put a CAP - BLANKING on each disconnected electrical connector.
     (g) Remove the screws (5) and the bracket (3).
   (2) Remove the oven from the aft galley:
     (a) Remove the screws (6) and the washers (4).
     (b) Carefully pull the oven (7) out of the mounting rails (1) and disconnect the electrical connector.
     (c) Remove the oven (7) from the galley.
     (d) Put a CAP - BLANKING on each disconnected electrical connector.
     (e) Remove the screws (5), the washers (4) and the bracket (3).
Subtask 25-35-19-020-050-AI ** ON A/C NOT FOR ALL
A. Removal of the Oven
F Oven ** ON A/C NOT FOR ALL
WARNING: SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
   (1) Prevent damage to the component interfaces and the adjacent area.
   (2) Remove the screws (2).
   (3) Carefully pull the oven (3) to disconnect the electrical connector.
   (4) Remove the oven (3) from the mounting rails (1).
   (5) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
Subtask 25-35-19-020-050-AX ** ON A/C NOT FOR ALL
A. Removal of the Oven
F Oven(s) ** ON A/C NOT FOR ALL
WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
WARNING: SUPPORT THE UNIT/ASSEMBLY. THE UNIT/ASSEMBLY IS HEAVY. IF YOU DO NOT SUPPORT IT, IT WILL FALL. THIS CAN CAUSE INJURY TO PERSONS, AND/OR DAMAGE TO EQUIPMENT.
   (1) Remove the oven (3) from the forward galley and aft galley G3B as follows:
     (a) Remove the screws (2).
     (b) Carefully pull the oven (3) to disconnect the electrical connector.
     (c) Remove the oven (3) from the galley.
     (d) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
   (2) Remove the oven (3) from aft galley G4B as follows:
     (a) Remove the screws (8) and the screen (7).
     (b) Remove the screws (6).
     (c) Carefully pull the oven (3) to disconnect the electrical connector.
     (d) Remove the oven (3) from the galley.
     (e) Remove the screws (5) and the bracket (4).
     (f) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
Subtask 25-35-19-020-050-LB ** ON A/C NOT FOR ALL
A. Removal of the Oven(s)
F Oven(s) ** ON A/C NOT FOR ALL
WARNING: DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
   (1) Prevent damage to the component interfaces and the adjacent area.
   (2) FOR [6475MM] (GALLEY LOC.I), [6480MM] (GALLEY LOC.III)
Remove the oven(s) (3) from the related galley as follows:
     (a) Remove the screws (2).
     (b) Carefully pull the oven(s) (3) out of the galley and disconnect the electrical connector(s).
     (c) Remove the oven(s) (3) from the mounting rails (1).
   (3) FOR [6482MM] (GALLEY LOC.IV A/B)
Remove the oven(s) (3) from the galley as follows:
     (a) Remove the sealant with the SCRAPER - NON METALLIC.
     (b) Remove the screws (8) and the screen(s) (7).
     (c) Remove the screws (6).
     (d) Carefully pull the oven(s) (3) out of the galley and disconnect the electrical connector(s).
     (e) Remove the screws (5) and the bracket(s) (4).
     (f) Remove the oven(s) (3) from the mounting rails (1).
   (4) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
[Rev.10 from 2021] 2026.03.31 23:34:25 UTC
"Aviabrain" 2025