DOC AIRBUS | AMM A320FRemove the Floor Covering above the Heated Floor Panels
TASK 25-28-42-010-001-A
Remove the Floor Covering above the Heated Floor Panels
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 25-28-42-861-055-A ** ON A/C NOT FOR ALL 4. Procedure
Subtask 25-28-42-020-053-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:33:17 UTC
Remove the Floor Covering above the Heated Floor Panels
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 2 | CHISEL - NON METALLIC |
| No specific | 2 | CUTTER - THIN BLADE |
| No specific | 2 | SCRAPER - NON METALLIC |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
Access to the Heated Floor Panels ("Conventional")Subtask 25-28-42-861-055-A ** ON A/C NOT FOR ALL 4. Procedure
Subtask 25-28-42-020-053-A ** ON A/C NOT FOR ALL
A. Removal of the Floor Covering from the Heated Floor Panels ("Conventional")
(2) Remove the NTF (1) and the Glass-Fiber Reinforced Plastic (GFRP) sheet (3) with a CHISEL - NON METALLIC and discard them.
(3) Cut the MYLAR foil (5) with a CUTTER - THIN BLADE around the contour of the heated floor panel.
(4) Make sure that the width of the MYLAR foil that remains in the cutout of the NTF is 50 mm (2.0 in.) minimum. If necessary, remove more NTF.
(5) Remove the MYLAR foil (5) from the heated floor panel with a SCRAPER - NON METALLIC.
Subtask 25-28-42-020-054-A ** ON A/C NOT FOR ALL CAUTION:
REMOVE THE FLOOR COVERING CAREFULLY TO PREVENT DAMAGE TO THE CABIN FLOOR PANELS.
CAUTION:
DO NOT CAUSE DAMAGE TO THE MOISTURE BARRIER FOIL (MYLAR).
(1) Carefully cut the Non-Textile Floor Covering (NTF) with a CUTTER - THIN BLADE. Make the cutout a minimum of 50mm (2.0 in.) larger than the heated floor panel you want to remove. (2) Remove the NTF (1) and the Glass-Fiber Reinforced Plastic (GFRP) sheet (3) with a CHISEL - NON METALLIC and discard them.
(3) Cut the MYLAR foil (5) with a CUTTER - THIN BLADE around the contour of the heated floor panel.
(4) Make sure that the width of the MYLAR foil that remains in the cutout of the NTF is 50 mm (2.0 in.) minimum. If necessary, remove more NTF.
(5) Remove the MYLAR foil (5) from the heated floor panel with a SCRAPER - NON METALLIC.
B. Removal of the Floor Covering from the Heated Floor Panels ("WULFMEYER")
(2) Remove the NTF (1) with a CHISEL - NON METALLIC and discard the NTF (1).
(3) Cut the MYLAR foil (3) with a CUTTER - THIN BLADE around the contour of the heated floor panel.
(4) Make sure that the width of the MYLAR foil that remains in the cutout of the NTF is 50 mm (2.0 in.) minimum. If necessary remove more NTF.
(5) Remove the MYLAR foil (3) on the heated floor panel with a SCRAPER - NON METALLIC.
CAUTION:
REMOVE THE FLOOR COVERING CAREFULLY TO PREVENT DAMAGE TO THE CABIN FLOOR PANELS.
CAUTION:
DO NOT CAUSE DAMAGE TO THE MOISTURE BARRIER FOIL (MYLAR).
(1) Carefully cut the NTF with a CUTTER - THIN BLADE. Make the cutout a minimum of 50mm (2.0 in.) larger than the heated floor panel you want to remove. (2) Remove the NTF (1) with a CHISEL - NON METALLIC and discard the NTF (1).
(3) Cut the MYLAR foil (3) with a CUTTER - THIN BLADE around the contour of the heated floor panel.
(4) Make sure that the width of the MYLAR foil that remains in the cutout of the NTF is 50 mm (2.0 in.) minimum. If necessary remove more NTF.
(5) Remove the MYLAR foil (3) on the heated floor panel with a SCRAPER - NON METALLIC.