Removal of the Engine Leasing-Plate Bracket

TASK 11-24-71-000-805-A
Removal of the Engine Leasing-Plate Bracket

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

ZONE: 430
ZONE: 440

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
430	ENG 1 AIR INTAKE, FAN AND ACCESS GEARBOX
440	ENG 2 AIR INTAKE, FAN AND ACCESS GEARBOX
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
438AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 11-00-00-960-002-A	Replacement of the Engine Leasing Plate
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
Engine Leasing-Plate Bracket

3. Job Set-up
Subtask 11-24-71-941-058-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Put a WARNING NOTICE(S) in position to tell persons not to start engine 1(2).
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 11-24-71-040-055-A ** ON A/C NOT FOR ALL

B. Deactivation of the Thrust Reverser

WARNING: MAKE SURE THAT THE THRUST REVERSER IS LOCKED. IF NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO THE REVERSER.

(1) Make the thrust reverser unserviceable for maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 11-24-71-010-059-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
448AR.
(2) Remove the engine leasing plate (Ref. AMM TASK 11-00-00-960-002).

4. Procedure
Subtask 11-24-71-020-055-A ** ON A/C NOT FOR ALL

A. Removal of the Engine Leasing-Plate Bracket

Engine Leasing-Plate Bracket ** ON A/C NOT FOR ALL

(1) Hold the engine leasing-plate bracket (1).
(2) Remove the nuts (2).
(3) Remove the engine leasing-plate bracket (1) from the fan case.

[Rev.10 from 2021] 2026.03.31 22:54:18 UTC