Failure of the Control of the Fuel Shut-off Valve on Engine 2

TASK 76-12-00-810-817-A
Failure of the Control of the Fuel Shut-off Valve on Engine 2

1. Possible Causes

aircraft wiring
RELAY-ENG/MASTER 2 [12QG]
ACTUATOR-LP FUEL VALVE, ENG 2 [10QG]
VALVE-LP FUEL, ENG 2 [13QM]
CTL SW-ENG/MASTER 2 [2KC]
ECU [4000KS]

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
ESPM 2045210
AMM 28-24-00-710-002	Operational Test of the ENG 1(2) LP Fuel Valve
ASM 282401
AMM 28-24-41-000-001	Removal of the LP Fuel Valve
AMM 28-24-41-400-001	Installation of the LP Fuel Valve
AMM 28-24-51-000-001	Removal of the LP Fuel Valve Actuator
AMM 28-24-51-400-001	Installation of the LP Fuel Valve Actuator
AMM 31-10-00-700-001	Test Program after Removal/Installation of a VU panel
AMM 71-00-00-710-003	Engine Automatic Start
AMM 73-21-60-000-001	Removal of the Electronic Control Unit (ECU)
AMM 73-21-60-400-001	Installation of the Electronic Control Unit (ECU)
ASM 761201

3. Fault Confirmation
Subtask 76-12-00-710-080-A ** ON A/C NOT FOR ALL

A. Test
Not applicable, the fault is evident.

4. Fault Isolation
Subtask 76-12-00-865-057-A ** ON A/C NOT FOR ALL

A. Table of the circuit breakers used in this procedure:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FUEL/LP VALVE/MOT1/ENG2	2QG	A09
121VU	FUEL/LP VALVE/MOT2/ENG2	4QG	M26

Subtask 76-12-00-810-065-B ** ON A/C NOT FOR ALL

B. If the fault symptom is identified by the CFDS message MASTER LEVER, HMU:

make sure that the LP fuel valve is open AMM 28-24-00-710-002.

(1) If the valve is not open:

do a check of the aircraft wiring between the circuit breakers (2QG) (4QG) and the ENG 2 LP fuel valve actuator (10QG) pins AA/A, BB/A ASM 761201 and ASM 282401.

(a) If there is no continuity:

repair the above wiring or/and replace the RELAY-ENG/MASTER 2 [12QG] .

(b) If there is continuity:

replace the ACTUATOR-LP FUEL VALVE, ENG 2 [10QG] AMM 28-24-51-000-001 and AMM 28-24-51-400-001.

replace the VALVE-LP FUEL, ENG 2 [13QM] AMM 28-24-41-000-001 and AMM 28-24-41-400-001.

(d) If the fault continues:

replace the CTL SW-ENG/MASTER 2 [2KC] on the panel 115VU ESPM 2045210.
install the panel 115VU and do a test program after removal/installation of a VU panel AMM 31-10-00-700-001.

(e) If the fault continues:

replace the ECU [4000KS] AMM 73-21-60-000-001 and AMM 73-21-60-400-001.

Subtask 76-12-00-710-081-A ** ON A/C NOT FOR ALL

C. Test
(1) Start the engine 2 by the engine automatic start procedure AMM 71-00-00-710-003.
(2) Make sure that there is no ECAM and CFDS fault message shown.

[Rev.8 from Aug 2018] 2026.04.04 04:37:27 UTC