DOC AIRBUS | TSM A320FEngine Thrust Levers not set at Correct Position
TASK 76-11-00-810-823-A
Engine Thrust Levers not set at Correct Position
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
3. Fault Confirmation
Subtask 76-11-00-710-091-A ** ON A/C NOT FOR ALL
Subtask 76-11-00-810-077-A ** ON A/C NOT FOR ALL
[Rev.8 from Aug 2018]
2026.04.04 04:37:26 UTC
Engine Thrust Levers not set at Correct Position
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
| REFERENCE | DESIGNATION |
|---|---|
| AMM 76-11-00-820-042 | Adjustment of the Mechanical Linkage |
| AMM 76-11-00-820-044 | Adjustment of the Mechanical Linkage |
| AMM 76-11-19-000-040 | Removal of the Throttle Control Unit |
| AMM 76-11-19-000-042 | Removal of the Throttle Control Unit |
| AMM 76-11-19-400-040 | Installation of the Throttle Control Unit |
| AMM 76-11-19-400-042 | Installation of the Throttle Control Unit |
Subtask 76-11-00-710-091-A ** ON A/C NOT FOR ALL
A. Make sure that the warning message ENG THR LEVERS NOT SET appeared when the thrust control levers were in the correct position.
4. Fault IsolationNOTE: This warning tells the crew that the flex temperature or the derated take off level is not set at take off . This warning is an operational warning, if the warning appears and it is sure that the thrust control levers are in an incorrect position. In this case, no maintenance action is necessary.
Subtask 76-11-00-810-077-A ** ON A/C NOT FOR ALL
A. If the warning message appeared and the thrust control levers were in the correct position, do the procedure that follows:
(1) Adjust the mechanical linkage AMM 76-11-00-820-042.
(2) Do the test given in AMM task AMM 76-11-19-400-040.
(a) Replace the CTL UNIT-THROTTLE, ENG 1 [8KS1] and CTL UNIT-THROTTLE, ENG 2 [8KS2] as necessary AMM 76-11-19-000-040 and AMM 76-11-19-400-040.
Subtask 76-11-00-810-077-B ** ON A/C NOT FOR ALL (1) Adjust the mechanical linkage AMM 76-11-00-820-042.
(2) Do the test given in AMM task AMM 76-11-19-400-040.
(a) Replace the CTL UNIT-THROTTLE, ENG 1 [8KS1] and CTL UNIT-THROTTLE, ENG 2 [8KS2] as necessary AMM 76-11-19-000-040 and AMM 76-11-19-400-040.
A. If the warning message appeared and the thrust control levers were in the correct position, do the procedure that follows:
(1) Adjust the mechanical linkage AMM 76-11-00-820-044.
(2) Do the test given in AMM task AMM 76-11-19-400-042.
(a) Replace the CTL UNIT-THROTTLE, ENG 1 [8KS1] and CTL UNIT-THROTTLE, ENG 2 [8KS2] as necessary AMM 76-11-19-000-042 and AMM 76-11-19-400-042.
(1) Adjust the mechanical linkage AMM 76-11-00-820-044.
(2) Do the test given in AMM task AMM 76-11-19-400-042.
(a) Replace the CTL UNIT-THROTTLE, ENG 1 [8KS1] and CTL UNIT-THROTTLE, ENG 2 [8KS2] as necessary AMM 76-11-19-000-042 and AMM 76-11-19-400-042.