Disagree between the DOOR/OXY Page of the ECAM System and the locked RH FWD Emergency Exit Door

TASK 52-22-00-810-802-A
Disagree between the DOOR/OXY Page of the ECAM System and the locked RH FWD Emergency Exit Door

1. Possible Causes

PROX SW-HOOK, R FWD EMER EXIT [59WV2]
SDAC-1 [1WV1]
SDAC-2 [1WV2]
wiring
C/B-EIS/SDAC1 AND 2/DOOR/DET/PAX [48WV]
IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2]
PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2]
C/B-EIS/SLIDES/ARM AND WARN/GND [13WN]

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
AMM 24-41-00-861-002	Energize the Aircraft Electrical Circuits from the External Power
ASM 315405
AMM 31-60-00-860-001	EIS Start Procedure
AMM 52-22-00-410-001	Closing of the Emergency Exit Doors from the Passenger Compartment
AMM 52-71-00-820-005	Adjustment of the Proximity Switches of the Emergency Exits with the CHECKING TOOL-DOORS
AMM 52-71-00-820-007	Adjustment of the Proximity Switches of the Emergency Exit Doors with the CHECKING TOOL-DOORS
AMM 52-71-13-000-003	Removal of the Proximity Switches
AMM 52-71-13-400-003	Installation of the Proximity Switches
AMM 52-73-22-000-003	Removal of the CABIN PRESSURE Warning Light Panel of the Emergency Exit
AMM 52-73-22-400-003	Installation of the CABIN PRESSURE Warning Light Panel of the Emergency Exit Door

3. Fault Confirmation
Subtask 52-22-00-860-051-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
AMM 24-41-00-861-002.
(2) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only)
AMM 31-60-00-860-001.

Subtask 52-22-00-865-051-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	EIS/SLIDES/ARM AND WARN/GND	13WN	P10
121VU	EIS/SDAC1 AND 2/DOOR/DET/PAX	48WV	P05

Subtask 52-22-00-710-051-A ** ON A/C NOT FOR ALL

C. Test
(1) Make sure that the RH FWD emergency exit door is closed and locked AMM 52-22-00-410-001.
(2) On the ECAM control panel:

push the DOOR key to get the DOOR/OXY page.

(3) On the DOOR/OXY page of the lower ECAM DU, look for possible fault indications.

4. Fault Isolation
Subtask 52-22-00-810-051-A ** ON A/C NOT FOR ALL

A. If the test gives the amber EMER EXIT indication of the RH FWD emergency exit door:

Do a check and adjust as necessary the PROX SW-HOOK, R FWD EMER EXIT [59WV2] AMM 52-71-00-820-005.

(1) If the fault continues:

Install the jumper wire between the PROX SW-HOOK, R FWD EMER EXIT [59WV2] connector A/C and A/B ASM 315405.

(a) If the message EMER EXIT goes off:

Replace the PROX SW-HOOK, R FWD EMER EXIT [59WV2] AMM 52-71-13-000-003 and AMM 52-71-13-400-003.
Remove the jumper wire.

(b) If the message EMER EXIT stays on:

Remove the jumper wire.
Do a check for a ground signal at the PROX SW-HOOK, R FWD EMER EXIT [59WV2] connector A/C ASM 315405.

1 If there is a ground signal:

Do a check and repair the wiring between the PROX SW-HOOK, R FWD EMER EXIT [59WV2] connector A/B and the SDAC-1 [1WV1] or the SDAC-2 [1WV2] connector AA/11C ASM 315405.

a If the fault continues:

Do a check for 28 VDC between the:
the PROX SW-HOOK, R FWD EMER EXIT [59WV2] connector A/A and A/D ASM 315405.

b If there is 28VDC:

Replace the PROX SW-HOOK, R FWD EMER EXIT [59WV2] AMM 52-71-13-000-003 and AMM 52-71-13-400-003.

c If there is no 28VDC, do a check and repair the wiring between:

The PROX SW-HOOK, R FWD EMER EXIT [59WV2] connector A/A and CB C/B-EIS/SDAC1 AND 2/DOOR/DET/PAX [48WV] , and the connector PROX SW-HOOK, R FWD EMER EXIT [59WV2] A/D and ground.

2 If there is no ground signal:

Do a check for continuity between the IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] connectors A/F and A/G ASM 315405.

a If there is no continuity:

Replace the IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] AMM 52-73-22-000-003 and AMM 52-73-22-400-003.

b If there is continuity:

Do a check and repair the wiring between:
The PROX SW-HOOK, R FWD EMER EXIT [59WV2] connector A/C and IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] connector A/G.
The PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] connector A/B and IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] connector A/F.

(2) If the fault continues:

Do a check and adjust as necessary the PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] AMM 52-71-00-820-007.

(3) If the fault continues:

Install the jumper wire between the PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] connector A/C and A/B ASM 315405.

(a) If the message EMER EXIT goes off:

Replace the PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] AMM 52-71-13-000-003 and AMM 52-71-13-400-003.
Remove the jumper wire.

(b) If the message EMER EXIT stays on:

Remove the jumper wire.
Do a check and repair the wiring between the PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] connector A/C and ground ASM 315405.

Do a check for 28VDC between the PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] connector A/A and A/D ASM 315405.

1 If there is no 28VDC:

Do a check for a continuity between the IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] connectors A/S and A/A ASM 315405.

a If there is continuity:

Do a check and repair the wiring between
IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] connector A/A and CB PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] , C/B-EIS/SLIDES/ARM AND WARN/GND [13WN] A/A and IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] A/S, PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] .

b If there is no continuity:

Replace the IND LT-SLIDE ARMED, FWD R EMERGENCY EXIT [21WN2] AMM 52-73-22-000-003 and AMM 52-73-22-400-003.

2 If there is 28VDC:

Replace the PROX SW-HANDLE FLAP, R FWD EMER EXIT [19WV2] AMM 52-71-13-000-003 and AMM 52-71-13-400-003.

5. Close-up
Subtask 52-22-00-710-072-A ** ON A/C NOT FOR ALL

A. Do the test as given in para. 3

[Rev.8 from Aug 2018] 2026.04.04 04:34:50 UTC