Sensor Monitoring Fault at the RH Passenger Compartment Emergency Exit
TASK 52-21-00-810-807-A
Sensor Monitoring Fault at the RH Passenger Compartment Emergency Exit
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
3. Fault Confirmation
Subtask 52-21-00-710-061-A ** ON A/C NOT FOR ALL
Subtask 52-21-00-810-058-A ** ON A/C NOT FOR ALL
Subtask 52-21-00-860-055-A ** ON A/C NOT FOR ALL
[Rev.8 from Aug 2018]
2026.04.04 04:34:49 UTC
Sensor Monitoring Fault at the RH Passenger Compartment Emergency Exit
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
| REFERENCE | DESIGNATION |
|---|---|
| AMM 24-41-00-862-002 | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| ASM 315405 | |
| AMM 31-60-00-860-001 | EIS Start Procedure |
| AMM 52-71-13-000-001 | Removal of the Proximity Switches |
| AMM 52-71-13-400-001 | Installation of the Proximity Switches |
| AMM 52-73-21-000-003 | Removal of the SLIDE ARMED Indicator-Light of the Emergency Exit |
| AMM 52-73-21-400-003 | Installation of the SLIDE ARMED Indicator-Light of the Emergency Exit |
Subtask 52-21-00-710-061-A ** ON A/C NOT FOR ALL
A. Test
(1) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only)
AMM 31-60-00-860-001.
(2) Remove and install the cover flap of the RH emergency exit hatch (refererd to as hatch).
(3) Look for the fault indications at the door page of the lower ECAM DU.
4. Fault Isolation(1) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only)
AMM 31-60-00-860-001.
(2) Remove and install the cover flap of the RH emergency exit hatch (refererd to as hatch).
(3) Look for the fault indications at the door page of the lower ECAM DU.
Subtask 52-21-00-810-058-A ** ON A/C NOT FOR ALL
A. When the cover flap is correctly installed and the door page of the lower ECAM DU shows the symbol for the hatch and the message EMER EXIT in amber:
Subtask 52-21-00-710-062-A ** ON A/C NOT FOR ALL - make sure that the adjustment of the PROX SW-HANDLE FLAP, R AFT EMER EXIT [21WV2] is correct AMM 52-71-13-400-001.
- make an electrical connection between the:
PROX SW-HANDLE FLAP, R AFT EMER EXIT [21WV2] connectors A/A and A/B ASM 315405.
- replace the PROX SW-HANDLE FLAP, R AFT EMER EXIT [21WV2] AMM 52-71-13-000-001 and AMM 52-71-13-400-001.
- do a check for 28 VDC between the:
PROX SW-HANDLE FLAP, R AFT EMER EXIT [21WV2] connectors A/A and A/C ASM 315405.
- do a check and repair the wiring between:
the PROX SW-HANDLE FLAP, R AFT EMER EXIT [21WV2] connector A/B and the IND LT-SLIDE ARMED, R EMER EXIT [2WN2] connector A/E ASM 315405.
- do a check and repair the wiring between the:
PROX SW-HANDLE FLAP, R AFT EMER EXIT [21WV2] connector A/A and the IND LT-SLIDE ARMED, R EMER EXIT [2WN2] connector A/R ASM 315405.
PROX SW-HANDLE FLAP, R AFT EMER EXIT [21WV2] connector A/C and ground ASM 315405.
- replace the IND LT-SLIDE ARMED, R EMER EXIT [2WN2] AMM 52-73-21-000-003 and AMM 52-73-21-400-003.
B. Do a test as given in Para. 3.A. to make sure that the operation is correct.
5. Close-upSubtask 52-21-00-860-055-A ** ON A/C NOT FOR ALL