W DOC AIRBUS | TSM A320F

Leak Detection of the Engine 2 Pylon Loop B

TASK 36-22-00-810-885-A
Leak Detection of the Engine 2 Pylon Loop B

1. Possible Causes
  • BMC-2 [1HA2]
  • CABLE-CONNECTING, R PYLON LOOP B [102HF2]
  • wiring
  • SENSING ELEMENT-OVHT, R PYLON LOOP B [101HF2]
  • SENSING ELEMENT-OVHT, R PYLON LOOP B [106HF2]
  • CABLE-CONNECTING, R PYLON LOOP B [104HF2]
  • CABLE-CONNECTING, R PYLON LOOP B [105HF2]
  • CABLE-CONNECTING, R PYLON LOOP B [103HF2]
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
9240SI
1
CONTROLLER-LOOP
 B. Referenced Information
REFERENCE
DESIGNATION
ESPM 204422
AMM 36-11-00-740-802
BITE Test of the Engine Bleed Air System (EBAS) (System Test)
AMM 36-11-34-000-001
Removal of the BMC
AMM 36-11-34-400-001
Installation of the BMC
ASM 362201
AMM 36-22-15-000-802
Removal of the Pylon Overheat Sensing-Elements
AMM 36-22-15-000-803
Removal of the Pylon Overheat Sensing-Elements
AMM 36-22-15-400-802
Installation of the Pylon Overheat Sensing-Elements
AMM 36-22-15-400-803
Installation of the Pylon Overheat Sensing-Elements
3. Fault Confirmation
Subtask 36-22-00-710-139-A ** ON A/C NOT FOR ALL
A. Test
   (1) Do the BITE test of the EBAS AMM 36-11-00-740-802.
4. Fault Isolation
Subtask 36-22-00-810-156-A ** ON A/C NOT FOR ALL
A. If the test gives the maintenance message:
ENG2 PYLON LOOP B()
   (1) If the impedance is more than 10 kOhms:
   (2) If the impedance is less than 10 kOhms:
  • Do a visual inspection of the sensing elements and cables on engine 2 pylon loop B.
     (a) If a sensing element or cable is damaged:
     (b) If no sensing element is damaged:
  • Disconnect the connector between cable 102HF2 and sensing element 101HF2.
  • Do a check of the impedance read on the 9240SI CONTROLLER-LOOP.
       1 If the impedance is less than 10 kOhms:
  • Replace the CABLE-CONNECTING, R PYLON LOOP B [102HF2] ESPM 204422.
  • Do a check of the impedance read on the 9240SI CONTROLLER-LOOP.
         a If the impedance is less than 10 kOhms:
  • Do a check and repair the wiring between pin AA/4D of BMC2 (1HA2) and the cable 102HF2 ASM 362201.
  • Connect all the cables or connectors disconnected.
  • Disconnect the 9240SI CONTROLLER-LOOP from the BMC2 connector.
  • Install BMC2 (1HA2) AMM 36-11-34-400-001.
  • Refer to Para. 4.B.
         b If the impedance is more than 10 kOhms:
  • Connect all the cables or connectors disconnected.
  • Disconnect the 9240SI CONTROLLER-LOOP from the BMC2 connector.
  • Install BMC2 (1HA2) AMM 36-11-34-400-001.
  • Refer to Para. 4.B.
       2 If the impedance is more than 10 kOhms:
  • Disconnect the connector between cable 103HF2 and sensing element 106HF2.
  • Connect the connector between cable 102HF2 and sensing element 101HF2.
  • Do a check of the impedance read on the 9240SI CONTROLLER-LOOP.
         a If the impedance is less than 10 kOhms:
  • Disconnect the connector between cable 104HF2 and sensing element 101HF2.
  • Connect the connector between cable 103HF2 and sensing element 106HF2.
  • Do a check of the impedance read on the 9240SI CONTROLLER-LOOP.

    * If the impedance is less than 17 kOhms:
    - Replace the SENSING ELEMENT-OVHT, R PYLON LOOP B [101HF2] AMM 36-22-15-000-803 and AMM 36-22-15-400-803.
    - Disconnect the 9240SI CONTROLLER-LOOP from the BMC2 connector.
    - Install BMC-2 [1HA2] AMM 36-11-34-400-001.
    - Refer to Para. 4.B.

    * If the impedance is more than 17 kOhms:
    - Disconnect the connector between cable 105HF2 and sensing element 106HF2.
    - Connect the connector between cable 104HF2 and sensing element 101HF2.
    - Do a check of the impedance read on the 9240SI CONTROLLER-LOOP.

    ** If the impedance is more than 10 kOhms:
    - Replace the SENSING ELEMENT-OVHT, R PYLON LOOP B [106HF2] AMM 36-22-15-000-802 and AMM 36-22-15-400-802.
    - Disconnect the 9240SI CONTROLLER-LOOP from the BMC2 connector.
    - Install BMC-2 [1HA2] AMM 36-11-34-400-001.
    - Refer to Para. 4.B.

    ** If the impedance is less than 10 kOhms:
    - Replace the CABLE-CONNECTING, R PYLON LOOP B [104HF2] and CABLE-CONNECTING, R PYLON LOOP B [105HF2] ESPM 204422.
    - Disconnect the 9240SI CONTROLLER-LOOP from the BMC2 connector.
    - Install BMC-2 [1HA2] AMM 36-11-34-400-001.
    - Refer to Para. 4.B.
         b If the impedance is more than 10 kOhms:
  • Replace the CABLE-CONNECTING, R PYLON LOOP B [103HF2] ESPM 204422.
  • Connect all the cables or connectors disconnected.
  • Do a check of the impedance read on the 9240SI CONTROLLER-LOOP.

    * If the impedance is less than 10 kOhms:
    - Do a check and repair the wiring between pin AA/5D of BMC2 (1HA2) and cable 103HF2 ASM 362201.
    - Disconnect the 9240SI CONTROLLER-LOOP from the BMC2 connector.
    - Install BMC2 (1HA2) AMM 36-11-34-400-001.
    - Refer to Para. 4.B.

    * If the impedance is more than 10 kOhms:
    - Disconnect the 9240SI CONTROLLER-LOOP from the BMC2 connector.
    - Install BMC2 (1HA2) AMM 36-11-34-400-001.
    - Refer to Para. 4.B.
Subtask 36-22-00-710-140-A ** ON A/C NOT FOR ALL
B. Do the test given in Para. 3.
[Rev.8 from Aug 2018] 2026.04.04 04:40:30 UTC
"AVIABRAIN" 2025