DOC AIRBUS | TSM A320FEngine 1 Bleed Temperature Sensor Measurement Failure
TASK 36-11-00-810-A05-A
Engine 1 Bleed Temperature Sensor Measurement Failure
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
3. Fault Confirmation
Subtask 36-11-00-710-460-A ** ON A/C NOT FOR ALL
Subtask 36-11-00-810-412-A ** ON A/C NOT FOR ALL
[Rev.8 from Aug 2018]
2026.04.04 04:33:55 UTC
Engine 1 Bleed Temperature Sensor Measurement Failure
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
| REFERENCE | DESIGNATION |
|---|---|
| ASM 361101 | |
| AMM 36-11-17-000-001 | Removal of the Heat-Exchanger Outlet-Temperature Sensor |
| AMM 36-11-17-400-001 | Installation of the Heat-Exchanger Outlet-Temperature Sensor |
| AMM 36-11-34-000-001 | Removal of the BMC |
| AMM 36-11-34-400-001 | Installation of the BMC |
Subtask 36-11-00-710-460-A ** ON A/C NOT FOR ALL
A. Test.
(1) Not Applicable
4. Fault Isolation(1) Not Applicable
Subtask 36-11-00-810-412-A ** ON A/C NOT FOR ALL
A. If the fault symptom is identified by the maintenance message:
TEMP SENSOR (6HA1)/BMC1 (1HA1)/BMC2 (1HA2)
Subtask 36-11-00-810-423-A ** ON A/C NOT FOR ALL TEMP SENSOR (6HA1)/BMC1 (1HA1)/BMC2 (1HA2)
- Replace the SENSOR-EXCHANGER OUT TEMP, ENG 1 [6HA1] AMM 36-11-17-000-001 and AMM 36-11-17-400-001.
B. If the fault continues:
(1) Do a check for ground for Exchanger Outlet Temperature-Sensor (6HA1) at pin G/1 of the BMC1 (1HA1).
(a) If there is no ground:
1 Do a check of the wiring from BMC1 (1HA1) pin G/1 and the ground terminal ASM 361101.
a If you find damage in the wiring:
1 Do a check of the wiring Exchanger Outlet Temperature-Sensor (6HA1) pin A/1 and A/2 to BMC1 (1HA1) pin AB/7D and AB/7E ASM 361101.
a If you find damage in the wiring:
a If you find damage in the wiring:
Subtask 36-11-00-810-424-A ** ON A/C NOT FOR ALL Subtask 36-11-00-810-425-A ** ON A/C NOT FOR ALL Subtask 36-11-00-710-461-A ** ON A/C NOT FOR ALL (1) Do a check for ground for Exchanger Outlet Temperature-Sensor (6HA1) at pin G/1 of the BMC1 (1HA1).
(a) If there is no ground:
1 Do a check of the wiring from BMC1 (1HA1) pin G/1 and the ground terminal ASM 361101.
a If you find damage in the wiring:
- Repair or replace the wiring .
1 Do a check of the wiring Exchanger Outlet Temperature-Sensor (6HA1) pin A/1 and A/2 to BMC1 (1HA1) pin AB/7D and AB/7E ASM 361101.
a If you find damage in the wiring:
- Repair or replace the wiring .
a If you find damage in the wiring:
- Repair or replace the wiring .
E. After the subsequent flight, make sure that the fault does not continue.