Loss of the VOR 1 Tuning Data

TASK 34-55-00-810-823-A
Loss of the VOR 1 Tuning Data

1. Possible Causes

FMGC-1 [1CA1]
wiring of the FMGC OWN CB 1 bus from the FMGC 1 (1CA1) to the first terminal block
RMP-COM/NAV FREQ SEL, 1 [1RG1]
wiring of the DATA FROM FMGC bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block
wiring of the NAV DATA OUTPUT bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block
RECEIVER-VOR/MKR, 1 [3RS1]
wiring of the FREQ FUNCT DATA SOURCE bus from the VOR/MKR receiver 1 (3RS1) to the first terminal block

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
AMM 22-83-34-000-001	Removal of the FMGC
AMM 22-83-34-400-001	Installation of the FMGC
ASM 228602
ASM 231301
AMM 23-13-13-000-001	Removal of the Radio Management Panel (RMP)
AMM 23-13-13-400-001	Installation of the Radio Management Panel (RMP)
AMM 34-14-00-740-001	Interface Test of the IR
AMM 34-36-00-740-002	BITE Test of the ILS
AMM 34-55-00-740-002	BITE Test of the VOR/MKR
ASM 345501
AMM 34-55-31-000-001	Removal of the VOR/MKR Receiver
AMM 34-55-31-400-001	Installation of the VOR/MKR Receiver

3. Fault Confirmation
Subtask 34-55-00-740-078-A

A. Test
(1) Do the BITE test of the VOR/MKR AMM 34-55-00-740-002.

4. Fault Isolation
Subtask 34-55-00-810-082-B

A. If the test gives the maintenance message FMGC(1CA1)/RMP1(1RG1)/VOR1(3RS1):

on the center pedestal, on the RMP 1, push the NAV and the VOR pushbutton switches (the green LED on these pushbutton switches comes on)
do the BITE test of the VOR/MKR AMM 34-55-00-740-002.

(1) If the test does not give the maintenance message FMGC1(1CA1)/RMP1(1RG1)/VOR1 (3RS1):

(a) If the Interface test of the IR gives the maintenance message ADIRU1 : NO FMGC 1 DATA:

1 If the fault continues:

do a check and repair the wiring of the FMGC OWN CB 1 bus from the FMGC 1 (1CA1) to the first terminal block ASM 228602.

(b) If the Interface test of the IR does not give the maintenance message ADIRU1 : NO FMGC1 DATA:

replace the RMP-COM/NAV FREQ SEL, 1 [1RG1] AMM 23-13-13-000-001 and AMM 23-13-13-400-001.

1 If the fault continues:

do a check and repair the wiring of the DATA FROM FMGC bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block ASM 231301.

(2) If the test gives again the maintenance message FMGC1(1CA1)/RMP1(1RG1)/VOD1 (3RS1):

(a) If the BITE test gives the maintenance message ILS1 : NO DATA FROM CONTROL SOURCE:

replace the RMP-COM/NAV FREQ SEL, 1 [1RG1] AMM 23-13-13-000-001 and AMM 23-13-13-400-001.

1 If the fault continues:

do a check and repair the wiring of the NAV DATA OUTPUT bus from the COM/NAV FREQ SEL RMP 1 (1RG1) to the first terminal block ASM 345501 .

(b) If the BITE test does not give the maintenance message ILS1 : NO DATA FROM CONTROL SOURCE:

1 If the fault continues:

do a check and repair the wiring of the FREQ FUNCT DATA SOURCE bus from the VOR/MKR receiver 1 (3RS1) to the first terminal block ASM 345501.

Subtask 34-55-00-740-079-A

B. Do the test given in Para. 3.

[Rev.8 from Aug 2018] 2026.04.04 04:33:32 UTC