Loss of the ADF 2 Tuning Data

TASK 34-53-00-810-812-A
Loss of the ADF 2 Tuning Data

1. Possible Causes

FMGC-2 [1CA2]
wiring of the FMGC OWN CB 1 bus from the FMGC 2 (1CA2) to the first terminal block
RMP-COM/NAV FREQ SEL, 2 [1RG2]
wiring of the DATA FROM FMGC bus from the COM/NAV FREQ SEL RMP 2 (1RG2) to the first terminal block
wiring of the NAV FREQ DATA OUTPUT bus from the COM/NAV FREQ SEL RMP 2 (1RG2) the first terminal block
RECEIVER-ADF, 2 [2RP2]
wiring of the FREQUENCY CONTROL PORT A bus from the ADF receiver 2 (2RP2) to the first terminal block

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
AMM 22-83-34-000-001	Removal of the FMGC
AMM 22-83-34-400-001	Installation of the FMGC
ASM 228602
ASM 231301
AMM 23-13-13-000-001	Removal of the Radio Management Panel (RMP)
AMM 23-13-13-400-001	Installation of the Radio Management Panel (RMP)
AMM 34-14-00-740-001	Interface Test of the IR
AMM 34-53-00-740-003	BITE Test of the ADF
ASM 345301
AMM 34-53-31-000-002	Removal of the ADF Receiver
AMM 34-53-31-400-002	Installation of the ADF Receiver
AMM 34-55-00-740-002	BITE Test of the VOR/MKR

3. Fault Confirmation
Subtask 34-53-00-740-072-A ** ON A/C NOT FOR ALL

A. Test
(1) Do the BITE test of the ADF AMM 34-53-00-740-003.

4. Fault Isolation
Subtask 34-53-00-810-063-A ** ON A/C NOT FOR ALL

A. If the test gives the maintenance message ADF2 : NO DATA FROM CONTROL SOURCE:

on the center pedestal, on the RMP 2, push the NAV and the ADF pushbutton switches (the green LED on these pushbutton switches comes on).
do the BITE test of the ADF AMM 34-53-00-740-003.

(1) If the test does not give the maintenance message ADF2 : NO DATA FROM CONTROL SOURCE:

(a) If the Interface test of the IR (system 1) gives a maintenance message related to a FMGC2 failure:

1 If the fault continues:

do a check and repair the wiring of the FMGC OWN CB 1 bus from the FMGC 2 (1CA2) to the first terminal block ASM 228602.

(b) If the Interface test of the IR (system 1) does not give a maintenance message related to a FMGC2 failure:

replace the RMP-COM/NAV FREQ SEL, 2 [1RG2] AMM 23-13-13-000-001 and AMM 23-13-13-400-001.

1 If the fault continues:

do a check and repair the wiring of the DATA FROM FMGC bus from the COM/NAV FREQ SEL RMP 2 (1RG2) to the first terminal block ASM 231301.

(2) If the test gives again the maintenance message ADF2 : NO DATA FROM CONTROL SOURCE:

(a) If the BITE test gives a maintenance message related to a RMP failure:

replace the RMP-COM/NAV FREQ SEL, 2 [1RG2] AMM 23-13-13-000-001 and AMM 23-13-13-400-001.

1 If the fault continues:

do a check and repair the wiring of the NAV FREQ DATA OUTPUT bus from the COM/NAV FREQ SEL RMP 2 (1RG2) the first terminal block ASM 345301.

(b) If the BITE test does not give a maintenance message related to a RMP failure:

1 If the fault continues:

do a check and repair the wiring of the FREQUENCY CONTROL PORT A bus from the ADF receiver 2 (2RP2) to the first terminal block ASM 345301.

Subtask 34-53-00-740-073-A ** ON A/C NOT FOR ALL

B. Do the test given in Para. 3.

[Rev.8 from Aug 2018] 2026.04.04 04:33:26 UTC