Loss of the MMR2 Data on the ADIRU3
TASK 34-36-00-810-879-A
Loss of the MMR2 Data on the ADIRU3
1. Possible Causes
A. Referenced Information
3. Fault Confirmation
Subtask 34-36-00-740-170-A 4. Fault Isolation
Subtask 34-36-00-810-148-B
[Rev.8 from Aug 2018]
2026.04.04 04:33:03 UTC
Loss of the MMR2 Data on the ADIRU3
1. Possible Causes
- MMR-2 [40RT2]
- MMR-1 [40RT1]
- wiring from the MMR1 to the ADIRU3
- wiring from the MMR2 to the ADIRU3
- ADIRU-3 [1FP3]
A. Referenced Information
| REFERENCE | DESIGNATION |
|---|---|
| AMM 34-12-34-000-001 | Removal of the ADIRU |
| AMM 34-12-34-400-001 | Installation of the ADIRU |
| AMM 34-14-00-740-004 | SYSTEM TEST of the Inertial Reference (IR) |
| AMM 34-36-00-740-003 | BITE Test of the MMR |
| ASM 343602 | |
| AMM 34-36-31-000-001 | Removal of the ILS Receiver |
| AMM 34-36-31-400-001 | Installation of the ILS Receiver |
Subtask 34-36-00-740-170-A 4. Fault Isolation
Subtask 34-36-00-810-148-B
A. If the test gives the maintenance message MMR2-GPSSU2(40RT2-1SN2)/ADIRU3 (1FP3):
(a) If the test gives a fault message:
a Remove the MMR1 and the MMR2 AMM 34-36-31-000-001.
b Remove the ADIRU3 AMM 34-12-34-000-001.
c Do a check and repair: ASM 343602
e Install the ADIRU3 AMM 34-12-34-400-001.
3 If the fault continues:
Subtask 34-36-00-740-171-A NOTE: In this case, the GPSSU2 message is for the GPS part of the MMR2.
(1) Do the BITE test of the MMR-2 [40RT2] AMM 34-36-00-740-003. (a) If the test gives a fault message:
- Do the related trouble shooting procedure.
- Do the BITE test of the MMR-1 [40RT1] AMM 34-36-00-740-003.
- Do the related trouble shooting procedure.
a Remove the MMR1 and the MMR2 AMM 34-36-31-000-001.
b Remove the ADIRU3 AMM 34-12-34-000-001.
c Do a check and repair: ASM 343602
- The wiring from the MMR1 to the ADIRU3 :
. Pins AB/9E, 9F to pins AB/14D, 15D for the GNSS INPUT 3 DATA bus
. Pins AB/7E, 7F to pins AB/14J, 15J for the GNSS INPUT 3 TIME MARK bus. - The wiring from the MMR2 to the ADIRU3 :
. Pins AB/9E, 9F to pins AB/7C, 8C for the GNSS INPUT 3 DATA bus
. Pins AB/7E, 7F to pins AB/1C, 2C for the GNSS INPUT 3 TIME MARK bus.
e Install the ADIRU3 AMM 34-12-34-400-001.
3 If the fault continues:
- Replace the ADIRU-3 [1FP3] AMM 34-12-34-000-001 and AMM 34-12-34-400-001.
B. Do the test given in Para. 3.