The FAULT Legend of the ADR3 Pushbutton Switch does not come on while the related Warning is shown on the Upper ECAM DU

TASK 34-13-00-810-917-A
The FAULT Legend of the ADR3 Pushbutton Switch does not come on while the related Warning is shown on the Upper ECAM DU

1. Possible Causes

ADIRU-3 [1FP3]
BOARD-ANN LT TEST & INTFC [4LP]
wiring of the ADR FAULT WARN discrete from the ADIRU3 (1FP3) to the annunciator light test and interface board (4LP)
CDU-ADIRS [2FP]
wiring of the annunciator light test and interface board (4LP)
wiring
P/BSW-ADIRS/ADR3 (26FP3)
wiring of the annunciator light test and interface board (4LP):

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
AMM 33-14-33-000-001	Removal of the Annunciator-Light Test and Interface-Board
AMM 33-14-33-400-001	Installation of the Annunciator-Light Test and Interface-Board
AMM 34-10-00-860-002	ADIRS Start Procedure
AMM 34-10-00-860-005	ADIRS Stop Procedure
AMM 34-12-12-000-001	Removal of the ADIRS CDU
AMM 34-12-12-400-001	Installation of the ADIRS CDU
AMM 34-12-34-000-001	Removal of the ADIRU
AMM 34-12-34-400-001	Installation of the ADIRU
ASM 341302

3. Fault Confirmation
Subtask 34-13-00-860-054-A

A. Job Set-Up
(1) Do the ADIRS start procedure AMM 34-10-00-860-002.

Subtask 34-13-00-865-061-A

B. Table of the circuit breakers used in this procedure:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	ADIRS/ADIRU/3/26VAC AND AOA	5FP3	N07

Subtask 34-13-00-710-137-A ** ON A/C NOT FOR ALL

C. Test

ACTION	RESULT
1.Open the circuit breaker (5FP3).	on the upper ECAM DU, the NAV ADR 3 FAULT warning comes into view on the ADIRS CDU, the FAULT legend of the ADR3 pushbutton switch comes on.

Subtask 34-13-00-710-137-B ** ON A/C NOT FOR ALL

C. Test

ACTION	RESULT
1.Open the circuit breaker (5FP3).	On the upper ECAM DU, the NAV ADR 3 FAULT warning comes into view. On the ADIRS MSU, the FAULT legend of the ADR3 annunciator comes on.

4. Fault Isolation
Subtask 34-13-00-810-167-A ** ON A/C NOT FOR ALL

A. If the FAULT legend of the ADR3 pushbutton switch does not come on:

on the overhead control and indicating panel 25VU, set the INT LT/ANN LT switch to TEST and make sure that the FAULT legend comes on.

(1) If the FAULT legend comes on:

replace the ADIRU-3 [1FP3] AMM 34-12-34-000-001 and AMM 34-12-34-400-001.

(a) If the FAULT legend stays off while the ECAM warning is shown:

replace the BOARD-ANN LT TEST & INTFC [4LP] AMM 33-14-33-000-001 and AMM 33-14-33-400-001.

1 If the fault continues:

do a check and repair the wiring of the ADR FAULT WARN discrete from the ADIRU3 (1FP3) to the annunciator light test and interface board (4LP) ASM 341302.

(2) If the FAULT legend does not come on:

replace the BOARD-ANN LT TEST & INTFC [4LP] AMM 33-14-33-000-001 and AMM 33-14-33-400-001.

(a) If the fault continues:

replace the CDU-ADIRS [2FP] AMM 34-12-12-000-001 and AMM 34-12-12-400-001.

1 If the fault continues:

do a check and repair the wiring of the annunciator light test and interface board (4LP)
. from pin A/44 to ADIRS CDU (2FP) pin C/22
. from pin A/12 to the first terminal block ASM 341302.

Subtask 34-13-00-810-167-B ** ON A/C NOT FOR ALL

A. If the FAULT legend of the ADR3 pushbutton switch does not come on:

On the overhead control and indicating panel 25VU, set the INT LT/ANN LT switch to TEST and make sure that the FAULT legend comes on.

(1) If the FAULT legend comes on:

Replace the ADIRU-3 [1FP3] AMM 34-12-34-000-001 and AMM 34-12-34-400-001.

(a) If the FAULT legend stays off while the ECAM warning is shown:

Replace the BOARD-ANN LT TEST & INTFC [4LP] AMM 33-14-33-000-001 and AMM 33-14-33-400-001.

1 If the fault continues:

Do a check and repair the wiring of the ADR FAULT WARN discrete from the ADIRU3 (1FP3) to the annunciator light test and interface board (4LP) ASM 341302.

(2) If the FAULT legend does not come on:

Replace the BOARD-ANN LT TEST & INTFC [4LP] AMM 33-14-33-000-001 and AMM 33-14-33-400-001.

(a) If the fault continues:

Replace the P/BSW-ADIRS/ADR3 (26FP3).

1 If the fault continues:

Do a check and repair the wiring of the annunciator light test and interface board (4LP):
. From pin A/44 to pin A/7 of the ADIRS/ADR3 pushbutton switch (26FP3)
. From pin A/12 to the first terminal block ASM 341302.

Subtask 34-13-00-710-138-A

B. Do the test given in Para. 3.

5. Close-up
Subtask 34-13-00-860-055-A

A. Put the aircraft back to its initial configuration.
(1) Close the circuit breaker (5FP3).
(2) On the panel 25VU, set the ANN LT switch to BRT.
(3) Do the ADIRS stop procedure AMM 34-10-00-860-005.

[Rev.8 from Aug 2018] 2026.04.04 04:32:28 UTC