CONFIG PARK BRK ON Warning is not Shown on the Upper ECAM DU with the PARK BRK Control Switch at ON

TASK 32-45-00-810-804-A
CONFIG PARK BRK ON Warning is not Shown on the Upper ECAM DU with the PARK BRK Control Switch at ON

1. Possible Causes

wiring from the pin B/D of the parking brake electrical control valve (72GG) to the ground terminal
CTL VALVE-PARK BRK,ELEC. [72GG]
wiring from the pin A/A of the parking brake pressure switch (86GG) to the parking brake electrical control valve (72GG) pin B/D.
PRESS SW-PARK BRK [86GG]
wiring from the parking brake electrical control valve (72GG) pin B/E to the SDAC (1WV1) pin AD/7C
wiring from the pin B/4 of the parking brake electrical control valve (102GG) t the ground terminal
CTL VALVE-PARK BRK, ELEC [102GG]
wiring from the parking brake electrical control valve (102GG) pin A/5 to the SDAC (1WV1; 1WV2) pin AD/7C

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
ASM 324501
AMM 32-45-17-000-001	Removal of the Park Brake - Pressure Switch
AMM 32-45-17-400-001	Installation of the Park Brake - Pressure Switch
AMM 32-45-51-000-001	Removal of the Parking-Brake Electrical Control-Valve
AMM 32-45-51-400-001	Installation of the Parking-Brake Electrical Control-Valve
AMM 32-45-53-000-001	Removal of the Parking-Brake Electrical Control-Valve
AMM 32-45-53-400-001	Installation of the Parking-Brake Electrical Control-Valve

3. Fault Confirmation
Subtask 32-45-00-710-052-A

A. Not applicable.

4. Fault Isolation
Subtask 32-45-00-810-053-B ** ON A/C NOT FOR ALL

A. If the CONFIG PARK BRK ON warning does not come into view when the PARK BRK control switch is at ON (during flight phases 3 and 4):

set the PARK BRK selector switch to ON.
do a check for a ground signal at pin B/E of the parking brake electrical control valve (72GG) ASM 324501.

(1) If there is no ground signal:

do a check for a ground signal at pin B/D of the parking brake electrical control valve (72GG) ASM 324501.

(a) If there is no ground signal:

do a check and repair the wiring from the pin B/D of the parking brake electrical control valve (72GG) to the ground terminal ASM 324501.

(b) If there is a ground signal:

(2) If there is a ground signal:

do a check for a ground signal at pin A/B of the parking brake pressure switch (86GG) ASM 324501.

(a) If there is no ground signal:

do a check for a ground signal at pin A/A of the parking brake pressure switch (86GG) ASM 324501.

1 If there is no ground signal:

do a check and repair the wiring from the pin A/A of the parking brake pressure switch (86GG) to the parking brake electrical control valve (72GG) pin B/D. ASM 324501.

2 If there is a ground signal:

(b) If there is a ground signal:

do a check and repair the wiring from the parking brake electrical control valve (72GG) pin B/E to the SDAC (1WV1) pin AD/7C ASM 324501.

Subtask 32-45-00-810-053-C ** ON A/C NOT FOR ALL

A. If the CONFIG PARK BRK ON warning does not come into view when the PARK BRK control switch is at ON (during flight phases 3 and 4):

Set the PARK BRK selector switch to ON.
Do a check for a ground signal at pin B/5 of the parking brake electrical control valve (102GG) ASM 324501.

(1) If there is no ground signal:

Do a check for a ground signal at pin B/4 of the parking brake electrical control valve (102GG) ASM 324501.

(a) If there is no ground signal:

Do a check and repair the wiring from the pin B/4 of the parking brake electrical control valve (102GG) t the ground terminal ASM 324501.

(b) If there is a ground signal:

(2) If there is a ground signal:

Do a check and repair the wiring from the parking brake electrical control valve (102GG) pin A/5 to the SDAC (1WV1; 1WV2) pin AD/7C ASM 324501.

Subtask 32-45-00-710-053-A

B. After the subsequent flight, make sure that the fault does not continue.

[Rev.8 from Aug 2018] 2026.04.04 04:31:45 UTC