W DOC AIRBUS | TSM A320F

Blank Screen on the Lower ECAM DU

TASK 31-63-82-810-838-A
Blank Screen on the Lower ECAM DU

1. Possible Causes
  • DU-ECAM, LOWER [4WT2]
  • wiring
  • C/B-EIS/ECAM DU/LOWER/SWTG [24WT2]
  • CTL PNL-ECAM [6WT]
2. Job Set-up Information
 A. Referenced Information
REFERENCE
DESIGNATION
AMM 31-60-00-860-001
EIS Start Procedure
AMM 31-60-00-860-002
EIS Stop Procedure
ASM 316102
AMM 31-63-22-000-001
Removal of the Display Unit
AMM 31-63-22-400-001
Installation of the Display Unit
ASM 316801
ASM 316803
3. Fault Confirmation
Subtask 31-63-82-860-095-A ** ON A/C NOT FOR ALL
A. Job Set-up
   (1) Do the EIS start procedure AMM 31-60-00-860-001.
4. Fault Isolation
Subtask 31-63-82-810-115-A ** ON A/C NOT FOR ALL
A. If the operational image is shown on the lower ECAM DU :
  • no maintenance action is necessary.
Subtask 31-63-82-810-116-A ** ON A/C NOT FOR ALL
B. If a maintenance message is shown on a black screen
  • do the fault isolation procedure relative to this message.
Subtask 31-63-82-810-117-A ** ON A/C NOT FOR ALL
C. If a blank screen (screen completely black) is shown on the lower ECAM DU:
   (1) If the fault continues:
     (a) Do a check for 115VAC at pin AA-79 of the lower ECAM DU ASM 316102.
       1 If there is no 115VAC:
  • check the wiring from the lower ECAM SPLY-C/B (13WT2) to the lower ECAM DU (4WT2) pin AA-79.
         a If there is no continuity:
  • repair the wiring.
         b If there is continuity:
  • replace the DU-ECAM, LOWER [4WT2] .
       2 If there is 115VAC:
  • do a check for a ground signal at pin A-77 of the lower ECAM DU.
         a If there is no ground signal:
  • check and repair the wiring from the lower ECAM-DU pin AA-77 to the the ground terminal.
         b If there is a ground signal:
  • do a check for 28VDC at the lower ECAM-DU pin AA-81
    . if there is no 28VDC, check and repair the wiring from the lower ECAM-DU pin AA-81 to the lower ECAM-SWTG C/B (24WT2)
    . if there is 28VDC, replace the C/B-EIS/ECAM DU/LOWER/SWTG [24WT2] .
   (2) If the fault continues:
  • do a check for a ground signal at pin AA-75 of the lower ECAM DU ASM 316803.
     (a) If there is a ground signal:
  • make sure there is no ground signal at pin A-D of the potentiometer (6WT).
       1 If there is no ground signal:
  • check and repair the wiring from the lower ECAM CTL-PNL (6WT) pin A-D to the lower ECAM DU (4WT2) pin AA-75.
       2 If there is a ground signal:
  • replace the CTL PNL-ECAM [6WT] .
   (3) If the fault continues:
  • do a check and repair the wiring ASM 316801.
    from the lower ECAM DU(4WT2) pin AA-39 to the lower ECAM CTL-PNL (6WT) pin A-B
    from the lower ECAM DU(4WT2) pin AA-40 to the lower ECAM CTL-PNL (6WT) pin A-C
    from the lower ECAM DU(4WT2) pin AA-36 to the lower ECAM CTL-PNL (6WT) pin A-U.
     (a) If the wiring is correct, replace the CTL PNL-ECAM [6WT] .
5. Close-up
Subtask 31-63-82-860-109-A ** ON A/C NOT FOR ALL
A. CLose-up
[Rev.8 from Aug 2018] 2026.04.04 04:31:16 UTC
"WTRUIB" 2025