Loss of the CAPT PFD, CAPT ND and Upper ECAM DU

TASK 31-63-82-810-801-A
Loss of the CAPT PFD, CAPT ND and Upper ECAM DU

1. Possible Causes

DMC-1 [1WT1]
wiring
C/B-EIS/DMC1/SPLY [10WT1]
DMC-3 [1WT3]
C/B-EIS/DMC3/SWTG [21WT3]

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
AMM 31-60-00-860-001	EIS Start Procedure
AMM 31-60-00-860-002	EIS Stop Procedure
ASM 316102
AMM 31-63-34-000-001	Removal of the DMC
AMM 31-63-34-400-001	Installation of the DMC

3. Fault Confirmation
Subtask 31-63-82-860-050-A ** ON A/C NOT FOR ALL

A. Job Set-up
Do the EIS start procedure (CAPT PFD, CAPT ND and upper ECAM DU only) AMM 31-60-00-860-001.

Subtask 31-63-82-700-050-A ** ON A/C NOT FOR ALL

B. Test
Make sure that the display units display a diagonal line.

4. Fault Isolation
Subtask 31-63-82-810-050-A ** ON A/C NOT FOR ALL

A. If the three display units display a diagonal line and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at NORM:
(1) Do a check for 115VAC at pin AC/2 of the DMC1 (1WT1) ASM 316102.
(a) If there is 115VAC:

replace the DMC-1 [1WT1] AMM 31-63-34-000-001 and AMM 31-63-34-400-001.

(b) If there is no 115VAC:

do a check for a ground signal at pin AC/7 of the DMC1 (1WT1).

1 If there is no ground signal:

repair the wiring from DMC1 (1WT1) pin AC/7 to the ground terminal.

2 If there is a ground signal:

do a check of the wiring from DMC1 (1WT1) pin AC/2 to the circuit breaker (10WT1).

a If there is no continuity:

repair the wiring.

b If there is continuity:

replace the C/B-EIS/DMC1/SPLY [10WT1] .

Subtask 31-63-82-810-051-A ** ON A/C NOT FOR ALL

B. If the three display units display a diagonal line and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at CAPT/3:
(1) Do a check for 28VDC at pin AC/3 of the DMC3 (1WT3) ASM 316102.
(a) If there is 28VDC:

replace the DMC-3 [1WT3] AMM 31-63-34-000-001 and AMM 31-63-34-400-001.

(b) If there is no 28VDC:

do a check for a ground signal at pin AC/11 of the DMC3 (1WT3)

1 If there is no ground signal:

repair the wiring from DMC3 (1WT3) pin AC/11 to the ground terminal.

2 If there is a ground signal:

do a check of the wiring from DMC3 (1WT3) pin AC/3 to the circuit breaker (21WT3).

a If there is no continuity:

repair the wiring.

b If there is continuity:

replace the C/B-EIS/DMC3/SWTG [21WT3] .

Subtask 31-63-82-700-051-A ** ON A/C NOT FOR ALL

C. Do the EIS start procedure (CAPT PFD, CAPT ND and upper ECAM DU only) AMM 31-60-00-860-001 and make sure that the display units come on.

5. Close-up
Subtask 31-63-82-860-051-A ** ON A/C NOT FOR ALL

A. Do the EIS stop procedure AMM 31-60-00-860-002.

[Rev.8 from Aug 2018] 2026.04.04 04:31:13 UTC