Permanent noise from the cockpit loudspeaker(s)
TASK 31-53-00-810-969-A
Permanent noise from the cockpit loudspeaker(s)
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
3. Fault Confirmation
Subtask 31-53-00-700-055-A
Subtask 31-53-00-810-219-A
Subtask 31-53-00-942-050-A
[Rev.8 from Aug 2018]
2026.04.04 04:30:22 UTC
Permanent noise from the cockpit loudspeaker(s)
1. Possible Causes
2. Job Set-up Information
A. Referenced Information
| REFERENCE | DESIGNATION |
|---|---|
| ASM 235106 | |
| AMM 23-51-34-000-001 | Removal of the Audio Management Unit (AMU) (1RN) |
| AMM 23-51-34-400-001 | Installation of the Audio Management Unit (AMU) (1RN) |
| AMM 31-53-34-000-001 | Removal of the Flight Warning Computer (FWC) |
| AMM 31-53-34-400-001 | Installation of the Flight Warning Computer (FWC) |
Subtask 31-53-00-700-055-A
A. Test
(1) Not applicable, the fault is evident.
4. Fault Isolation(1) Not applicable, the fault is evident.
Subtask 31-53-00-810-219-A
A. If there is confirmation of the fault:
(1) Replace the FWC for which the fault occurred:
Subtask 31-53-00-810-220-A (1) Replace the FWC for which the fault occurred:
- FWC-1 [1WW1] or FWC-2 [1WW2] AMM 31-53-34-000-001 and AMM 31-53-34-400-001.
B. If the fault continues:
Do a check and repair the wiring of the FWC for which the fault occurred.
(1) For the FWC1
(a) Remove the FWC1 AMM 31-53-34-000-001.
(b) Remove the AMU AMM 23-51-34-000-001.
(c) Do a check and repair the wiring from:
(e) Install the FWC1 AMM 31-53-34-400-001.
(f) Do the test(s) given in the Para. Fault Confirmation.
(2) For the FWC2
(a) Remove the FWC2 AMM 31-53-34-000-001.
(b) Remove the AMU AMM 23-51-34-000-001.
(c) Do a check and repair the wiring from:
(e) Install the FWC2 AMM 31-53-34-400-001.
(f) Do the test(s) given in the Para. Fault Confirmation.
5. Close-upDo a check and repair the wiring of the FWC for which the fault occurred.
(1) For the FWC1
(a) Remove the FWC1 AMM 31-53-34-000-001.
(b) Remove the AMU AMM 23-51-34-000-001.
(c) Do a check and repair the wiring from:
- The FWC1 pin AA/7G to the AMU pin AB/12H
- The AMU pin AB/13H to the ground terminal block
ASM 235106.
(e) Install the FWC1 AMM 31-53-34-400-001.
(f) Do the test(s) given in the Para. Fault Confirmation.
(2) For the FWC2
(a) Remove the FWC2 AMM 31-53-34-000-001.
(b) Remove the AMU AMM 23-51-34-000-001.
(c) Do a check and repair the wiring from:
- The FWC2 pin AA/7G to the AMU pin AB/12H
- The AMU pin AB/13H to the ground terminal block
ASM 235106.
(e) Install the FWC2 AMM 31-53-34-400-001.
(f) Do the test(s) given in the Para. Fault Confirmation.
Subtask 31-53-00-942-050-A
A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tools and other items.
(1) Make sure that the work area is clean and clear of tools and other items.