Loss of the Right Windshield Temperature Sensor

TASK 30-42-00-810-804-A
Loss of the Right Windshield Temperature Sensor

1. Possible Causes

WINDSHIELD-R [3DG2]
WHC-2 [2DG2]
wiring from the WHC 2 (2DG2) to the R windshield (3DG2)
wiring from the WHC 2 (2DG2) to R windshield (3DG2)

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
ESPM 2044110
AMM 30-42-00-710-001	Operational Test of the Windshield Anti-Icing and Defogging
ASM 304202
AWM 304202
AMM 30-42-34-000-001	Removal of the Window Heat Computer (WHC)
AMM 30-42-34-400-001	Installation of the Window Heat Computer (WHC)
AMM 56-11-11-000-001	Removal of the Windshield
AMM 56-11-11-400-001	Installation of the Windshield
R Windshield Electrical Connector
Sensor Resistance Versus Temperature

3. Fault Confirmation
Subtask 30-42-00-710-056-A

A. Test
(1) Do the operational test of the windshield anti-icing and defogging AMM 30-42-00-710-001.

4. Fault Isolation
Subtask 30-42-00-865-052-A

A. Table of the circuit breakers used in this procedure:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
122VU	ANTI ICE/WHC/2	5DG2	W13

Subtask 30-42-00-810-053-B ** ON A/C NOT FOR ALL

B. If the test gives the maintenance message R WINDSHIELD SENSOR associated with ECAM warning ANTI-ICE R WINDSHIELD, or ANTI-ICE R WINDOW:
(1) If the ECAM warning is triggered on ground with OAT greater than 40 deg.C or if the cockpit window/windshield is directly heading to the sun and air conditioning packs selected off:

Select air conditioning PACK on.
After 5 minutes, open and close C/B 5DG2 to reset WHC2.

(2) If the fault continues:

Disconnect the electrical connector from the R windshield (3DG2) and do a check of the resistance between pins A/C and A/D on the receptacle of the R windshield (3DG2).
R Windshield Electrical Connector ** ON A/C NOT FOR ALL

(a) If the resistance is out of the limits (more than 715 ohms (open circuit) or less than 370 ohms (short circuit)) or is not correct (see 'sensor resistance versus temperature' abacus):

Sensor Resistance Versus Temperature ** ON A/C NOT FOR ALL

NOTE: If only one sensor is available we recommend the replacement of the WINDSHIELD-R (3DG2) if you operate in icing conditions.

Make sure that the connector pins are not damaged.
Do a check of the resistance of the sensor 3 between pins A/D and A/E for correct value.
R Windshield Electrical Connector ** ON A/C NOT FOR ALL

1 If the resistance of the sensor 3 is correct:

Disconnect the wiring from pin A/D (or A/F) and connect it to pin A/E AWM 304202 and ASM 304202.

disconnect the wiring from pin A/C (or A/E) and connect it to pin A/D AWM 304202 and ASM 304202.

2 If the resistance of the sensor 3 is out of the limits (more than 715 ohms (open circuit) or less than 370 ohms (short circuit)) or is not correct (see 'sensor resistance versus temperature' abacus) and if a third sensor is installed in the windshield (in relation with the part number) :

Sensor Resistance Versus Temperature ** ON A/C NOT FOR ALL

Make sure that the connector pins are not damaged.
Do a check of the resistance of the sensor 2 between pins A/E and A/F for correct value.
R Windshield Electrical Connector ** ON A/C NOT FOR ALL

a If the resistance of the sensor 2 is correct:

Disconnect the wiring from pin A/C and connect it to pin A/E AWM 304202 and ASM 304202.

Disconnect the wiring from pin A/D and connect it to pin A/F AWM 304202 and ASM 304202.

b If the resistance of the sensor 2 is not correct or is out of limits:

Replace the WINDSHIELD-R [3DG2] AMM 56-11-11-000-001 and AMM 56-11-11-400-001.
Put the wiring back to its serviceable configuration AWM 304202 and ASM 304202.

3 If the fault continues:

Replace the WHC-2 [2DG2] , AMM 30-42-34-000-001 and AMM 30-42-34-400-001.

4 If the fault continues:

Do a check and repair the wiring from the WHC 2 (2DG2) to the R windshield (3DG2) pins B/A and B/B to pins A/C and A/D or pins B/A and B/B to pins A/E and A/F or pins B/A and B/B to pins A/D and A/E.

(b) If the resistance is correct:

Replace the WHC-2 [2DG2] , AMM 30-42-34-000-001 and AMM 30-42-34-400-001.

1 If the fault continues:

Do a check and repair the wiring from the WHC 2 (2DG2) to the R windshield (3DG2) pins B/A and B/B to pins A/C and A/D or pins B/A and B/B to pins A/E and A/F or pins B/A and B/B to pins A/D and A/E.

2 If the fault continues:

Replace the WINDSHIELD-R [3DG2] , AMM 56-11-11-000-001 and AMM 56-11-11-400-001.

Subtask 30-42-00-810-053-C ** ON A/C NOT FOR ALL

B. If the test gives maintenance message R WINDSHIELD SENSOR:

Disconnect the electrical connector from the R windshield (3DG2) and do a check of the resistance between pins A/C and A/D on the receptacle of the R windshield (3DG2).
R Windshield Electrical Connector

(1) If the resistance is out of the limits (more than 715 ohms (open circuit) or less than 370 ohms (short circuit)) or is not correct (see 'sensor resistance versus temperature' abacus):

Sensor Resistance Versus Temperature

NOTE: If only one sensor is available we recommend the replacement of the WINDSHIELD-R (3DG2) if you operate in icing conditions.

Make sure that the connector pins are not damaged.
Do a check of the resistance of sensor 3 between pins A/D and A/E for correct value.
R Windshield Electrical Connector

(a) If the resistance of sensor 3 is correct:

Connect pins B/A and B/B of the WHC2 (2DG2) to pins A/D and A/E of sensor 3 ESPM 2044110 and ASM 304202.

(b) If the resistance of sensor 3 is out of the limits (more than 715 ohms (open circuit) or less than 370 ohms (short circuit)) or is not correct (see 'sensor resistance versus temperature' abacus):

Sensor Resistance Versus Temperature

Make sure that the connector pins are not damaged.
Do a check of the resistance of sensor 2 between pins A/E and A/F for correct value.
R Windshield Electrical Connector

1 If the resistance of sensor 2 is correct:

Connect pins B/A and B/B of the WHC2 (2DG2) to pins A/E and A/F of sensor 2 ESPM 2044110 and ASM 304202.

2 If sensor 2 resistance is not correct:

Replace WINDSHIELD-R [3DG2] , AMM 56-11-11-000-001 and AMM 56-11-11-400-001.

Replace WHC-2 [2DG2] , AMM 30-42-34-000-001 and AMM 30-42-34-400-001.

(d) If the fault continues:

Do a check and repair the wiring from the WHC 2 (2DG2) to R windshield (3DG2) pins B/A and B/B to pins A/C and A/D or pins B/A and B/B to pins A/E and A/F.

(2) If the resistance is correct:

Replace WHC-2 [2DG2] , AMM 30-42-34-000-001 and AMM 30-42-34-400-001.

(a) If the fault continues:

Do a check and repair the wiring from the WHC 2 (2DG2) to R windshield (3DG2) pins B/A and B/B to pins A/C and A/D or pins B/A and B/B to pins A/E and A/F.

(b) If the fault continues:

Replace WINDSHIELD-R [3DG2] , AMM 56-11-11-000-001 and AMM 56-11-11-400-001.

Subtask 30-42-00-710-057-A

C. Do the operational test given in Para. 3.

[Rev.8 from Aug 2018] 2026.04.04 04:29:41 UTC