W DOC AIRBUS | TSM A320F

Loss of the Pressure of the Eng 2 Pump

TASK 29-13-00-810-804-A
Loss of the Pressure of the Eng 2 Pump

1. Possible Causes
  • PUMP VARIABLE DTS [3030GD]
  • ENG 2 PUMP P/BSW (3703GD)
  • wiring
  • ENG-HYD.-PUMP-SW [3074GD]
2. Job Set-up Information
 A. Referenced Information
REFERENCE
DESIGNATION
AMM 29-00-00-280-006
Check of the Green or Yellow Hydraulic System after Engine Pump Failure or Operation in a Possible Cavitation Condition - with Ground Cart Available
AMM 29-13-00-710-002
Operational Test of the Yellow Hydraulic System
ASM 291301
AMM 29-13-17-000-040
Removal of the Engine-Pump Pressure Switch
AMM 29-13-17-000-802
Removal of the Engine-Pump Pressure Switch
AMM 29-13-17-400-040
Installation of the Engine-Pump Pressure Switch
AMM 29-13-17-400-802
Installation of the Engine-Pump Pressure Switch
AMM 29-13-51-000-003
Removal of the Yellow Engine Pump
AMM 29-13-51-000-004
Removal of the Yellow Engine Pump
AMM 29-13-51-000-806
Removal of the Yellow Engine Driven Pump
AMM 29-13-51-100-801
Cleaning of the Engine Pump Solenoid-Valve
AMM 29-13-51-100-802
Cleaning of the Engine Pump Solenoid-Valve
AMM 29-13-51-100-804
Cleaning of the Engine Pump Solenoid-Valve
AMM 29-13-51-400-003
Installation of the Yellow Engine Pump
AMM 29-13-51-400-004
Installation of the Yellow Engine Pump
AMM 29-13-51-400-806
Installation of the Yellow Engine Driven Pump
3. Fault Confirmation
Subtask 29-13-00-710-052-A
A. Do the operational test of the Yellow hydraulic system AMM 29-13-00-710-002.
4. Fault Isolation
Subtask 29-13-00-810-055-A ** ON A/C NOT FOR ALL
A. If the test gives:
  • The message HYD Y ENG 2 PUMP LO PR on the upper ECAM DU
  • The LO flag of the Yellow hydraulic system on the HYD page of the lower ECAM DU
  • The PTU running indication on the HYD page of the lower ECAM DU
NOTE: The PRESS SW-Y PUMP, ENG 2 (3074GD) sends a low pressure signal to the ECAM system. This causes the PTU running indication on the lower ECAM DU, although the PTU does not operate (non system failure).
  • The Yellow ENG 2 PUMP P/BSW FAULT light on panel 40VU:

  • Look on the HYD page of the lower ECAM DU and do a check of the pressure of the Yellow system.
   (1) If the pressure is less than 1667 psi (114.9356 bar):
  • Do a check on the lower ECAM DU to make sure that the engine pump fire valve 3046GK is not closed.
     (a) If the engine pump fire valve is closed:
       1 Do a check of the engine pump for a possible cavitation condition AMM 29-00-00-280-006.
NOTE: A cavitation condition of the engine pump is possible when the engine pump operates with the engine pump fire valve closed (if you set the ENG 1 (2) FIRE pushbutton on the Eng/APU fire panel), or with the reservoir below the low level (ECAM indication).
       2 Push the ENG 2 FIRE P/BSW on panel 1WD (ENG/APU FIRE section on the overhead panel 20VU) to open the engine pump fire valve 3046GK.
     (b) If the engine pump fire valve is not closed:
  • Do a check for 28 VDC between:
    PUMP VARIABLE DTS [3030GD] connector A/1 and PUMP VARIABLE DTS [3030GD] connector A/3 ASM 291301.
       1 If there is no 28 VDC:
         a Clean the Solenoid Valve of the PUMP VARIABLE DTS [3030GD] AMM 29-13-51-100-801.
         b Do the test given in Para. 3.
         c If the fault continues:
         d Replace the PUMP VARIABLE DTS [3030GD] AMM 29-13-51-000-003 and AMM 29-13-51-400-003.
         e Do a check of the engine pump for a possible cavitation condition AMM 29-00-00-280-006.
NOTE: A cavitation condition of the engine pump is possible when the engine pumpoperates with the engine pump fire valve closed (if you set the ENG 1 (2) FIRE pushbutton on the Eng/APU fire panel), or with the reservoir below the low level (ECAM indication).
       2 If there is 28 VDC:
  • Replace the ENG 2 PUMP P/BSW (3703GD).
       3 If the fault continues:
  • Do a check of the wiring between:
    PUMP VARIABLE DTS [3030GD] connector A/3 and CB (3701GD) and repair the wiring as necessary ASM 291301.
   (2) If the pressure is more than 1812 psi (124.9330 bar):
  • Do a check for continuity between:
    the ENG-HYD.-PUMP-SW [3074GD] connector A/1 and A/3 ASM 291301.
     (a) If there is continuity:
     (b) If there is no continuity:
  • Make sure that the wiring is not connected to GND between:
    ENG-HYD.-PUMP-SW [3074GD] connector A/1 and the DIODE (1156VD) connector 43 ASM 291301.
     (c) If the wiring is connected to GND:
  • Repair the wiring as necessary.
Subtask 29-13-00-810-055-C ** ON A/C NOT FOR ALL
A. If the test gives:
  • The message HYD Y ENG 2 PUMP LO PR on the upper ECAM DU
  • The LO flag of the Yellow hydraulic system on the HYD page of the lower ECAM DU
  • The PTU running indication on the HYD page of the lower ECAM DU
NOTE: The PRESS SW-Y PUMP, ENG 2 (3074GD) sends a low pressure signal to the ECAM system. This causes the PTU running indication on the lower ECAM DU, although the PTU does not operate (non system failure).
  • The Yellow ENG 2 PUMP P/BSW FAULT light on panel 40VU:

  • Look on the HYD page of the lower ECAM DU and do a check of the pressure of the Yellow system.
   (1) If the pressure is less than 1667 psi (114.9356 bar):
  • Do a check on the lower ECAM DU to make sure that the engine pump fire valve 3046GK is not closed.
     (a) If the engine pump fire valve is closed:
       1 Do a check of the engine pump for a possible cavitation condition AMM 29-00-00-280-006.
NOTE: A cavitation condition of the engine pump is possible when the engine pump operates with the engine pump fire valve closed (if you set the ENG 1 (2) FIRE pushbutton on the Eng/APU fire panel), or with the reservoir below the low level (ECAM indication).
       2 Push the ENG 2 FIRE P/BSW on panel 1WD (ENG/APU FIRE section on the overhead panel 20VU) to open the engine pump fire valve 3046GK.
     (b) If the engine pump fire valve is not closed:
  • Do a check for 28 VDC between:
    PUMP VARIABLE DTS [3030GD] connector A/1 and PUMP VARIABLE DTS [3030GD] connector A/3 ASM 291301.
       1 If there is no 28 VDC:
         a Clean the Solenoid Valve of the PUMP VARIABLE DTS [3030GD] AMM 29-13-51-100-802.
         b Do the test given in Para. 3.
         c If the fault continues:
         d Replace the PUMP VARIABLE DTS [3030GD] AMM 29-13-51-000-004 and AMM 29-13-51-400-004.
         e Do a check of the engine pump for a possible cavitation condition AMM 29-00-00-280-006.
NOTE: A cavitation condition of the engine pump is possible when the engine pumpoperates with the engine pump fire valve closed (if you set the ENG 1 (2) FIRE pushbutton on the Eng/APU fire panel), or with the reservoir below the low level (ECAM indication).
       2 If there is 28 VDC:
  • Replace the ENG 2 PUMP P/BSW (3703GD).
       3 If the fault continues:
  • Do a check of the wiring between:
    PUMP VARIABLE DTS [3030GD] connector A/3 and CB (3701GD) and repair the wiring as necessary ASM 291301.
   (2) If the pressure is more than 1812 psi (124.9330 bar):
  • Do a check for continuity between:
    the ENG-HYD.-PUMP-SW [3074GD] connector A/1 and A/3 ASM 291301.
     (a) If there is continuity:
     (b) If there is no continuity:
  • Make sure that the wiring is not connected to GND between:
    ENG-HYD.-PUMP-SW [3074GD] connector A/1 and the DIODE (1156VD) connector 43 ASM 291301.
     (c) If the wiring is connected to GND:
  • Repair the wiring as necessary.
Subtask 29-13-00-810-055-D ** ON A/C NOT FOR ALL
A. If the test gives:
  • The message HYD Y ENG 2 PUMP LO PR on the upper ECAM DU
  • The LO flag of the Yellow hydraulic system on the HYD page of the lower ECAM DU
  • The PTU running indication on the HYD page of the lower ECAM DU
NOTE: The PRESS SW-Y PUMP, ENG 2 (3074GD) sends a low pressure signal to the ECAM system. This causes the PTU running indication on the lower ECAM DU, although the PTU does not operate (non system failure).
  • The Yellow ENG 2 PUMP P/BSW FAULT light on panel 40VU:

  • Look on the HYD page of the lower ECAM DU and do a check of the pressure of the Yellow system.
   (1) If the pressure is less than 1667 psi (114.9356 bar):
  • Do a check on the lower ECAM DU to make sure that the engine pump fire valve 3046GK is not closed.
     (a) If the engine pump fire valve is closed:
       1 Do a check of the engine pump for a possible cavitation condition AMM 29-00-00-280-006.
NOTE: A cavitation condition of the engine pump is possible when the engine pump operates with the engine pump fire valve closed (if you set the ENG 1 (2) FIRE pushbutton on the Eng/APU fire panel), or with the reservoir below the low level (ECAM indication).
       2 Push the ENG 2 FIRE P/BSW on panel 1WD (ENG/APU FIRE section on the overhead panel 20VU) to open the engine pump fire valve 3046GK.
     (b) If the engine pump fire valve is not closed:
  • Do a check for 28 VDC between:
    PUMP VARIABLE DTS [3030GD] connector A/1 and PUMP VARIABLE DTS [3030GD] connector A/3 ASM 291301.
       1 If there is no 28 VDC:
         a Clean the Solenoid Valve of the PUMP VARIABLE DTS [3030GD] AMM 29-13-51-100-804.
         b Do the test given in Para. 3.
         c If the fault continues:
         d Replace the PUMP VARIABLE DTS [3030GD] AMM 29-13-51-000-806 and AMM 29-13-51-400-806.
         e Do a check of the engine pump for a possible cavitation condition AMM 29-00-00-280-006.
NOTE: A cavitation condition of the engine pump is possible when the engine pumpoperates with the engine pump fire valve closed (if you set the ENG 1 (2) FIRE pushbutton on the Eng/APU fire panel), or with the reservoir below the low level (ECAM indication).
       2 If there is 28 VDC:
  • Replace the ENG 2 PUMP P/BSW (3703GD).
       3 If the fault continues:
  • Do a check of the wiring between:
    PUMP VARIABLE DTS [3030GD] connector A/3 and CB (3701GD) and repair the wiring as necessary ASM 291301.
   (2) If the pressure is more than 1812 psi (124.9330 bar):
  • Do a check for continuity between:
    the ENG-HYD.-PUMP-SW [3074GD] connector A/1 and A/3 ASM 291301.
     (a) If there is continuity:
     (b) If there is no continuity:
  • Make sure that the wiring is not connected to GND between:
    ENG-HYD.-PUMP-SW [3074GD] connector A/1 and the DIODE (1156VD) connector 43 ASM 291301.
     (c) If the wiring is connected to GND:
  • Repair the wiring as necessary.
Subtask 29-13-00-710-056-A
B. Do the test as given in Para. 3. A. to make sure that operation is correct.
[Rev.8 from Aug 2018] 2026.04.04 04:29:25 UTC
"WTRUIB" 2025