W DOC AIRBUS | TSM A320F

Fuel LP Fuel Valve Engine 2 Does Not Open

TASK 28-24-00-810-805-A
Fuel LP Fuel Valve Engine 2 Does Not Open

WARNING: OBEY THE FUEL SAFETY PROCEDURES.
WARNING: WHEN YOU DO WORK ON THE FUEL SYSTEM WIRING, YOU MUST USE TEST EQUIPMENT THAT IS APPROVED (REFER TO INTERNATIONAL OR NATIONAL SPECIFICATIONS FOR INTRINSICALLY SAFE TEST EQUIPMENT: EN50020, UL913 OR EQUIVALENT). TEST EQUIPMENT THAT IS NOT APPROVED CAN CAUSE FIRE OR AN EXPLOSION.
1. Possible Causes
  • ACTUATOR-LP FUEL VALVE, ENG 2 [10QG]
  • VALVE-LP FUEL, ENG 2 [13QM]
  • RELAY-ENG/MASTER 2 [12QG]
  • CTL SW-ENG/MASTER 2 [2KC]
  • ENG/APU FIRE PNL [1WD]
  • aircraft wiring
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
MULTIMETER - STANDARD
 B. Referenced Information
REFERENCE
DESIGNATION
ESPM 2046000
ESPM 2053210
AMM 26-12-00-00-
AMM 26-12-12-000-004
Removal of the FIRE Pushbutton Switch (ENG/APU Fire Panel)
AMM 26-12-12-400-004
Installation of the FIRE Pushbutton Switch (ENG/APU Fire Panel)
AMM 26-21-00-00-
ASM 262102
AMM 28-24-00-00-
AMM 28-24-00-710-002
Operational Test of the ENG 1(2) LP Fuel Valve
ASM 282401
AWM 282402
AMM 28-24-41-000-001
Removal of the LP Fuel Valve
AMM 28-24-41-400-001
Installation of the LP Fuel Valve
AMM 28-24-51-000-001
Removal of the LP Fuel Valve Actuator
AMM 28-24-51-400-001
Installation of the LP Fuel Valve Actuator
AMM 76-12-00-00-
ASM 761201
AWM 940602
TSM TASK 28-24-00-03
ENGINE LP FUEL SHUT OFF - TASK SUPPORTING DATA
3. Fault Confirmation
Subtask 28-24-00-710-053-A
A. Test
   (1) At the overhead panel 20VU, make sure that the ENG 2 FIRE PUSH pushbutton switch (on the ENG/APU FIRE PANEL 1WD) is in the closed and guarded position.
   (2) Get the Operational Test of the ENG 1(2) LP Fuel Valve 12QM (13QM) AMM 28-24-00-710-002.
     (a) Do the job set-up and sections of the test applicable to the Test of the Valve 13QM (the engine 2 LP valve).
       1 If the test:

  • operates as specified, do Para. 4. C.

  • shows that the motor 1 does not operate (when the C/B-4QG is opened and the operation of motor 2 prevented), do Para. 4.A.

  • shows that the motor 2 does not operate (when the C/B-2QG is opened and the operation of motor 1 prevented), do Para. 4.B.

  • shows that the motor 1 and 2 do not operate, do Para. 4.A. and 4.B.
NOTE: You can get more data from the:
4. Fault Isolation
Subtask 28-24-00-810-054-A
A. Procedure

The Actuator 10QG Motor 1 Does Not Operate From The Closed To The Open Position.
   (1) Get access to the actuator 10QG AMM 28-24-51-000-001.
     (a) Make sure that the actuator 10QG and the LP valve 13QM:
  • are correctly engaged together
  • V-clamp is correctly installed.
       1 If necessary, re-install the actuator 10QG AMM 28-24-51-400-001.
     (b) Do a visual inspection for signs of damage to the items that follow:
  • the connector 10QG-A and its supply cable
  • the actuator electrical related receptacle.
NOTE: Right Wing Wire Routing AWM 940602.
       1 Replace (or do a repair of) all the unserviceable wiring and connectors ESPM 2053210.
     (c) Do the test given in Para. 3.A.
   (2) Disconnect the electrical supply cable connector 10QG-A from the ACTUATOR-LP FUEL VALVE, ENG 2 (10QG).
   (3) Do a test, with a MULTIMETER - STANDARD, to see if the 28VDC supply is available at the connector 10QG-A between the pins as shown in the table that follows:
MOTOR 1 ARMATURE SIGNAL
CONNECTOR 10QG-A PIN
28VDC OPEN SUPPLY
A
GROUND
E
     (a) If the supply voltage at the connector 10QG-A:

  • is correct, do step (4)

  • is not correct, do step (5).
   (4) Replace the ACTUATOR-LP FUEL VALVE, ENG 2 [10QG] AMM 28-24-51-000-001 and AMM 28-24-51-400-001.
     (a) Do the test given in Para. 3.A.
     (b) If the fault continues, replace the VALVE-LP FUEL, ENG 2 [13QM] AMM 28-24-41-000-001 and AMM 28-24-41-400-001.
     (c) Do the test given in Para. 3.A.
   (5) Do a check of and replace, if necessary, the items that follow ASM 282401:
     (a) The RELAY-ENG/MASTER 2 [12QG] .
     (b) The CTL SW-ENG/MASTER 2 [2KC] (part of ENG PNL 115VU).
     (c) The ENG/APU FIRE PNL [1WD] .
     (d) Do the test given in Para. 3.A.
   (6) If the fault continues:
     (a) Do a check of the aircraft wiring AWM 282402 between:
  • the ACTUATOR-LP FUEL VALVE, ENG 2 connector 10QG-A, pin A and the RELAY-ENG/MASTER 2 (12QG), terminal A3
  • the ACTUATOR-LP FUEL VALVE, ENG 2 connector 10QG-A, pin E and the ground point 4002VN(621STA332)
  • the RELAY-ENG/MASTER 2 (12QG), terminal A2 and the ENG/APU FIRE PANEL (1WD) connector 1WD-D, pin <G
  • the ENG/APU FIRE PANEL (1WD) connector 1WD-D, pin <H and the C/B-FUEL/LP VALVE/MOT 1/ENG 2 (2QG), terminal 2.
     (b) Repair all the unserviceable wiring and connectors ESPM 2053210.
     (c) Do the test given in Para. 3.A.
Subtask 28-24-00-810-065-A
B. Procedure

The Actuator 10QG Motor 2 Does Not Operate From The Closed To The Open Position.
   (1) Get access to the actuator 10QG AMM 28-24-51-000-001.
     (a) Make sure that the actuator 10QG and the LP valve 13QM:
  • are correctly engaged together
  • V-clamp is correctly installed.
       1 If necessary, re-install the actuator 10QG AMM 28-24-51-400-001.
     (b) Do a visual inspection for signs of damage to the items that follow:
  • the connector 10QG-B and its supply cable
  • the actuator electrical related receptacle.
NOTE: Right Wing Wire Routing AWM 940602.
       1 Replace (or do a repair of) all the unserviceable wiring and connectors ESPM 2053210.
     (c) Do the test given in Para. 3.A.
   (2) Disconnect the electrical supply cable connector 10QG-B from the ACTUATOR-LP FUEL VALVE, ENG 2 (10QG).
   (3) Do a test, with a MULTIMETER - STANDARD, to see if the 28VDC supply is available at the connector 10QG-B between the pins as shown in the table that follows:
MOTOR 2 ARMATURE SIGNAL
CONNECTOR 10QG-B PIN
28VDC OPEN SUPPLY
A
GROUND
E
     (a) If the supply voltage at the connector 10QG-B:

  • is correct, do step (4)

  • is not correct, do step (5).
   (4) Replace the ACTUATOR-LP FUEL VALVE, ENG 2 [10QG] AMM 28-24-51-000-001 and AMM 28-24-51-400-001.
     (a) Do the test given in Para. 3.A.
     (b) If the fault continues, replace the VALVE-LP FUEL, ENG 2 [13QM] AMM 28-24-41-000-001 and AMM 28-24-41-400-001.
     (c) Do the test given in Para. 3.A.
   (5) Do a check of and replace, if necessary, the items that follow ASM 282401:
     (a) The RELAY-ENG/MASTER 2 [12QG] .
     (b) The CTL SW-ENG/MASTER 2 [2KC] (part of ENG PNL 115VU).
     (c) The ENG/APU FIRE PNL [1WD] .
     (d) Do the test given in Para. 3.A.
   (6) If the fault continues:
     (a) Do a check of the aircraft wiring AWM 282402 between:
  • the ACTUATOR-LP FUEL VALVE, ENG 2 connector 10QG-B, pin A and the RELAY-ENG/MASTER 2 (12QG), terminal B3
  • the ACTUATOR-LP FUEL VALVE, ENG 2 connector 10QG-B, pin E and the ground point 4004VN(622STA450)
  • the RELAY-ENG/MASTER 2 (12QG), terminal B2 and the ENG/APU FIRE PANEL (1WD) connector 1WD-C, pin <A
  • the ENG/APU FIRE PANEL (1WD) connector 1WD-C, pin <B and the C/B-FUEL/LP VALVE/MOT 2/ENG 2 (4QG), terminal 2.
     (b) Repair all the unserviceable wiring and connectors ESPM 2053210.
     (c) Do the test given in Para. 3.A.
Subtask 28-24-00-810-070-A
C. The Actuator 10QG does operate from the open to the closed position.
   (1) On the overhead panel 20VU, make sure the ENG 2 FIRE PUSH P/BSW (on the ENG/APU FIRE PANEL 1WD) is in the closed and guarded position.
   (2) On the panel 115VU, make sure the ENG/MASTER 2 switch is in the OFF position.
   (3) Use a MULTIMETER - STANDARD ASM 761201 ASM 282401 to do a check for a ground signal on the:
  • 1WD ENG/APU FIRE PANEL connector D, pin <H
  • 2KC CTL SW-ENG/MASTER 2 pin 3A.
     (a) If there is no ground signal on the 1WD ENG/APU FIRE PANEL connector D, pin <H:
     (b) If there is no ground signal on the 2KC CTL SW-ENG/MASTER 2 pin 3A:
  • Replace the CTL SW-ENG/MASTER 2 [2KC] (part of the panel 115VU) ESPM 2046000.
     (c) If there is a ground signal on both of the pins:
       1 Do a check of the aircraft wiring ASM 761201 between the:
  • 2KC CTL SW-ENG/MASTER 2 pin 2A and the 1KS2 EIU-2 connector AA, pin 4E
  • 2KC CTL SW-ENG/MASTER 2 pin 3A and the 1KS2 EIU-2 connector AA, pin 5A.
       2 Repair the unserviceable wiring and connectors ESPM 2053210.
     (d) Do the test given in the Para. 3. A.
[Rev.8 from Aug 2018] 2026.04.04 04:39:37 UTC
"AVIABRAIN" 2025