W DOC AIRBUS | TSM A320F

Loss of the Side Stick Priority Signal (New-Generation Side-Stick Unit)

TASK 27-92-00-810-842-A
Loss of the Side Stick Priority Signal (New-Generation Side-Stick Unit)

NOTE: This task is applicable only for the new-generation side-stick unit.
1. Possible Causes
  • RELAY-TAKEOVER & PRIORITY 1 [47CE1]
  • wiring
  • CAPT Side Stick Control-Handle (New-Generation Side Stick)
  • wiring from the connector 2197VC
  • F/O Side Stick Control-Handle (New-Generation Side Stick)
  • wiring from the connector 2188VC
  • SEC-1 [1CE1]
  • ELAC-1 [2CE1]
  • RELAY-TAKEOVER & PRIORITY 2 [47CE2]
  • wiring from the connector 2199VC
  • wiring from the connector 2190VC
  • SEC-3 [1CE3]
  • SEC-2 [1CE2]
  • ELAC-2 [2CE2]
2. Job Set-up Information
 A. Referenced Information
REFERENCE
DESIGNATION
AIPC 279208
ASM 279217
AMM 27-92-41-000-803
Removal of the Control-Handle of the New-Generation Side-Stick Unit
AMM 27-92-41-400-803
Installation of the Control-Handle of the New-generation Side-Stick Unit
AWM 279293
AWM 279294
AMM 27-93-34-000-001
Removal of the ELAC
AMM 27-93-34-400-001
Installation of the ELAC
AMM 27-94-34-000-001
Removal of the SEC
AMM 27-94-34-400-001
Installation of the SEC
AMM 27-96-00-710-003
Operational Test of the Side Stick Priority
AMM 27-96-00-740-001
BITE Test of the EFCS (Ground Scanning)
3. Fault Confirmation
Subtask 27-92-00-700-057-A
A. Test
   (1) Do the operational test of the side stick priority AMM 27-96-00-710-003.
   (2) Do the BITE test of the EFCS (Ground Scanning) AMM 27-96-00-740-001.
4. Fault Isolation
Subtask 27-92-00-810-098-A
A. If the tests give the maintenance message CHECK PRIORITY WIRING:
   (1) Do the tests given in Para. 3. with only the SEC 1 and the ELAC 1 engaged for the operational test of the side stick priority (SEC 2, SEC 3, ELAC 2 pushbuttons OFF).
  • If the tests do not give the maintenance message:
    . Go to paragraph (2).
  • If the tests give the maintenance message again:
     (a) Do the same tests:
  • With action on the CAPT takeover and priority pushbutton switch for the operational test of the side stick priority.
       1 If the tests give the maintenance message again:
  • Do the same tests with action on the F/O takeover and priority pushbutton switch for the operational test of the side stick priority.
         a If the tests give the maintenance message again:
  • Replace the RELAY-TAKEOVER & PRIORITY 1 [47CE1] AIPC 279208.
  • If the fault continues:
    . Do a check and repair the wiring from the relay (47CE1) pins A/1, 2, X, Z to the first terminal block and from pin A/A to the ground terminal ASM 279217.
  • If the fault continues, go to paragraph (b).
         b If the tests do not give the maintenance message:
  • Replace the CAPT Side Stick Control-Handle (New-Generation Side Stick) AMM 27-92-41-000-803 and AMM 27-92-41-400-803.
  • If the fault continues:
    . Do a check and repair the wiring from the connector 2197VC , pins S, A and B to the first terminal block AWM 279293.
  • If the fault continues, go to paragraph (b).
       2 If the tests do not give the maintenance message:
         a Replace the F/O Side Stick Control-Handle (New-Generation Side Stick) AMM 27-92-41-000-803 and AMM 27-92-41-400-803.
         b If the fault continues:
  • Do a check and repair the wiring from the connector 2188VC , pins S, A and B, to the first terminal block AWM 279293.
         c If the fault continues, go to paragraph (b).
     (b) Remove the ELAC 1 AMM 27-93-34-000-001 from its rack.
  • Do the tests given in Para. 3. with the SEC 1 engaged (SEC 2, SEC 3, ELAC 2 pushbuttons OFF).
       1 If the tests give the maintenance message again:
         a Reinstall the ELAC 1 AMM 27-93-34-400-001.
         b Replace the SEC-1 [1CE1] AMM 27-94-34-000-001 AMM 27-94-34-400-001.
         c If the fault continues:
  • Do a check of the insulation of the DSI 29, DSI 30 of the SEC-1 [1CE1] and repair it.
       2 If the tests do not give the maintenance message:
         a Replace the ELAC-1 [2CE1] AMM 27-93-34-400-001.
         b If the fault continues:
  • Do a check of the insulation of the DSI 35, DSI 36 of the ELAC-1 [2CE1] and repair it.
   (2) Do the tests given in Para. 3.:
  • With the SEC 2, SEC 3 and ELAC 2 engaged (SEC 1, ELAC 1 pushbuttons OFF).
  • With action on the CAPT takeover and priority pushbutton switch for the operational test of the side stick priority.
     (a) If the tests give the maintenance message:
  • Do the same tests with action on the F/O takeover and priority pushbutton switch for the operational test of the side stick priority.
       1 If the tests give the maintenance message again:
         a Replace the RELAY-TAKEOVER & PRIORITY 2 [47CE2] AIPC 279208.
         b If the fault continues:
. Do a check and repair the wiring from the relay (47CE2) pins A/1, 2, X, Z to the first terminal block and from pin A/A to the ground terminal ASM 279217.
         c If the fault continues, go to paragraph (c).
       2 If the tests do not give the maintenance message:
         a Replace the CAPT Side Stick Control-Handle (New-Generation Side Stick) AMM 27-92-41-000-803 and AMM 27-92-41-400-803.
         b If the fault continues:
. Do a check and repair the wiring from the connector 2199VC , pins H, J and K to the first terminal block AWM 279294.
         c If the fault continues, go to paragraph (c).
     (b) If the tests do not give the maintenance message:
       1 Replace the F/O Side Stick Control-Handle (New-Generation Side Stick) AMM 27-92-41-000-803 and AMM 27-92-41-400-803.
       2 If the fault continues:
  • Do a check and repair the wiring from the connector 2190VC , pins H, J and K to the first terminal block AWM 279294.
       3 If the fault continues, go to paragraph (c).
     (c) Remove the SEC 3 AMM 27-94-34-000-001 from its rack.
  • Do the tests given in Para. 3. with the SEC 2 and ELAC 2 engaged (SEC 1, ELAC 1, pushbuttons OFF).
       1 If the tests do not give the maintenance message:
         a Replace the SEC-3 [1CE3] AMM 27-94-34-400-001.
         b If the fault continues:
  • Do a check of the insulation of the DSI 29, DSI 30 of the SEC-3 [1CE3] and repair it.
       2 If the tests give the maintenance message again:
         a Reinstall the SEC 3 AMM 27-94-34-400-001.
         b Go to paragraph (d).
     (d) Remove the SEC 2 AMM 27-94-34-000-001 from its rack.
  • Do the tests again with the SEC 3 and ELAC 2 engaged (SEC 1, ELAC 1, pushbuttons OFF).
       1 If the tests do not give the maintenance message:
         a Replace the SEC-2 [1CE2] AMM 27-94-34-400-001.
         b If the fault continues:
  • Do a check of the insulation of the DSI 29, DSI 30 of the SEC 3 and repair it.
       2 If the tests give the maintenance message again:
         a Reinstall the SEC 2 AMM 27-94-34-400-001.
         b Go to paragraph (e).
     (e) Replace the ELAC-2 [2CE2] AMM 27-93-34-000-001 AMM 27-93-34-400-001.
       1 If the fault continues:
  • Do a check of the insulation of the DSI 35, DSI 36 of the ELAC-2 [2CE2] and repair it.
Subtask 27-92-00-700-058-A
B. Do the tests given in Para. 3.
[Rev.8 from Aug 2018] 2026.04.04 04:27:55 UTC
"WTRUIB" 2025