W DOC AIRBUS | TSM A320F

Loss of Detection by Engine-1 Loop A and Loop B AGB

TASK 26-12-00-810-864-A
Loss of Detection by Engine-1 Loop A and Loop B AGB

1. Possible Causes
  • DET-FIRE, ENG 1 PYLON LOOP A [3WD1]
  • DET-FIRE, CORE VENT LOOP A [4001WD1]
  • DET-FIRE, CORE AGB LOOP A [4002WD1]
  • HARNESS-FIRE DET, ENG 1 PYLON LOOP A STUD A [31WD1]
  • HARNESS-FIRE DET, ENG 1 PYLON LOOP A STUD C [32WD1]
  • wiring
  • FDU-ENG1 [2WD1]
  • terminal-block
2. Job Set-up Information
 A. Referenced Information
REFERENCE
DESIGNATION
TSM TASK 26-12-00-810-855-A
Loss of Detection by Engine-1 Loop-B AGB
AMM 26-12-00-200-802
Visual Inspection of the Engine Fire Detection System
AMM 26-12-00-710-002
Operational Test of the Engine Fire and Overheat Detection with the Centralized Fault Display System (CFDS)
ASM 261201
AWM 261205
AMM 26-12-16-000-803
Removal of the Pylon Fire Detector
AMM 26-12-16-400-803
Installation of the Pylon Fire Detector
AMM 26-12-17-000-802
Removal of the Forward Fire/Overheat Detector
AMM 26-12-17-000-803
Removal of the Aft Fire/Overheat Detector
AMM 26-12-17-400-802
Installation of the Forward Fire/Overheat Detector
AMM 26-12-17-400-803
Installation of the Aft Fire/Overheat Detector
AMM 26-12-34-000-001
Removal of the Engine Fire-Detection Unit (FDU)
AMM 26-12-34-400-001
Installation of the Engine Fire-Detection Unit (FDU)
AMM 26-12-63-000-801
Removal of the Pylon Fire-Detector Harness
AMM 26-12-63-400-801
Installation of the Pylon-Fire Detector Harness
AWM 715175
3. Fault Confirmation
Subtask 26-12-00-710-176-A ** ON A/C NOT FOR ALL
A. Test
   (1) Do the operational test of the engine fire and overheat detection from the Multipurpose Control and Display Unit (MCDU) AMM 26-12-00-710-002.
4. Fault Isolation
Subtask 26-12-00-810-215-B ** ON A/C NOT FOR ALL
A. If the test confirms the fault:
   (1) Do a visual inspection of the:
  • Engine-1-pylon loop-A fire-detector (3WD1),
  • Core-ventilation loop-A fire-detector (4001WD1)
  • Core-AGB loop-A fire-detector (4002WD1)
  • Engine-1-pylon fire-detector harnesses (31WD1) and (32WD1), AMM 26-12-00-200-802.
     (a) If one or more fire detector(s) is (are) damaged:
     (b) If there is no visual damage:
  • Do the trouble shooting given in Para 4.B.
Subtask 26-12-00-810-119-A ** ON A/C NOT FOR ALL
B. If the test confirms the fault:
  • Disconnect connector 2WD1-A from the engine 1 FDU (2WD1).
  • On the connector, on the wiring side, do a check of the equivalent resistance value between pins A/J and A/K, ASM 261201.
   (1) If the resistance value is between 3078 ohms and 3402 ohms:
  • Do a check of the wiring between the engine-1-pylon loop-A fire-detector (3WD1) and the first terminal block, AWM 261205.
     (a) If the wiring is not correct:
  • Disconnect the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1) from the engine-1-pylon loop-A fire-detector (3WD1).
  • On the responder, make sure that the resistance value is between 4275 ohms and 4725 ohms between pins A/A and A/C, ASM 261201.
       1 If the resistance values are out of the specified limits:
       2 If the resistance values are in the specified limits:
  • Do a continuity test of the wiring of the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1), AWM 261205.

         a If there is no continuity:
         b If there is continuity:
  • Do a check and repair the wiring between first terminal-block and the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1), AWM 261205.
  • Connect the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1) to the engine-1-pylon loop-A fire-detector (3WD1).
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).

     (b) If the wiring is correct:
  • Connect the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1) to the engine-1-pylon loop-A fire-detector (3WD1).
  • Do a check of the wiring between the first terminal-block and the core-AGB loop-A fire-detector (4002WD1), AWM 715175.
       1 If the wiring is not correct:
  • Repair it.
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
       2 If the wiring is correct:
         a If the fault continues:
   (2) If the resistance value is between 4275 ohms and 4725 ohms:
  • Do a check of the wiring between, AWM 261205 and AWM 715175:
    . Pin A/C of the core-ventilation loop-A fire-detector (4001WD1) and the first terminal-block
    . Pin A/A of the core-ventilation loop-A fire-detector (4001WD1) and the first terminal-block
    . Pin A/C of the core-AGB loop-A fire-detector (4002WD1) and the first terminal-block
    . Pin A/A of the core-AGB loop-A fire-detector (4002WD1) and the first terminal-block.
     (a) If the wiring is not correct:
  • Replace it (them).
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
     (b) If the wiring is correct:
   (3) If the resistance value is between 6469.5 ohms and 7150.5 ohms:
  • Do a check of the wiring between the engine-1-pylon loop-A fire-detector (3WD1) and the first terminal-block, AWM 261205.
     (a) If the wiring is not correct:
  • Disconnect the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1) from the engine-1-pylon loop-A fire-detector (3WD1).
  • On the responder, make sure that the resistance value is between 4275 ohms and 4725 ohms between pins A/A and A/C, ASM 261201.
       1 If the resistance values are out of the specified limits:
       2 If the resistance values are in the specified limits:
  • Do a continuity test of the wiring of the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1), AWM 261205.

         a If there is no continuity:
- Replace it (them):
. For HARNESS-FIRE DET, ENG 1 PYLON LOOP A STUD A [31WD1] AMM 26-12-63-000-801 and AMM 26-12-63-400-801.
. For HARNESS-FIRE DET, ENG 1 PYLON LOOP A STUD C [32WD1] AMM 26-12-63-000-801 and AMM 26-12-63-400-801.
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).

         b If there is continuity:
  • Do a check and repair the wiring between the first terminal-block and the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1), AWM 261205.
  • Connect the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1) to the engine-1-pylon loop-A fire-detector (3WD1).
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).

       3 If the wiring is correct:
  • Connect the engine-1-pylon fire-detector harnesses (31WD1) and (32WD1) to the engine-1-pylon loop-A fire-detector (3WD1).
  • Do a check of the wiring between the first terminal-block and the core -ventilation loop-A fire-detector (4001WD1), AWM 261205 and AWM 715175.
         a If the wiring is not correct:
  • Repair it.
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
     (b) If the wiring is correct:
       1 If the fault continues:
   (4) If the resistance value is infinite:
     (a) Do a check of the wiring between, AWM 261205:
  • Pin A/K of the connector 2WD1-A and the first terminal-block
  • Pin A/J of the connector 2WD1-A and the first terminal-block.
       1 If the wiring is not correct:
  • Repair it (them).
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
       2 If the wiring is correct:
  • Do a check of the wiring between, ASM 261201:
    . Pin A/K of the connector 2WD1-A and pin A/C of the core-ventilation loop-A fire-detector (4001WD1)
    . Pin A/J of the connector 2WD1-A and pin A/A of the core-ventilation loop-A fire-detector (4001WD1)
    . Pin A/K of the connector 2WD1-A and pin A/C of the core-AGB loop-A fire-detector (4002WD1)
    . Pin A/J of the connector 2WD1-A and pin A/A of the core-AGB loop-A fire-detector (4002WD1)
    . Pin A/K of the connector 2WD1-A and pin A/C of the engine-1-pylon loop-A fire-detector (3WD1)
    . Pin A/J of the connector 2WD1-A and pin A/A of the engine-1-pylon loop-A fire-detector (3WD1).
         a If the wiring is not correct:
  • Repair it (them).
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
         b If the wiring is correct:
   (5) If the resistance value is between 225 ohms and 1312.1 ohms:
  • Do a visual check for water on all the connections:
     (a) If there is water:
  • Clean the connection(s).
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
     (b) If there is no water:
  • On the responder of the engine-1-pylon loop-A fire-detector (3WD1), apply 45VDC voltage and make sure that the insulation resistance value is more than 100 Mohms.
       1 If the insulation resistance value is not correct:
       2 If the insulation resistance value is correct:
         a On the responders of the core-AGB loop-A fire-detector (4002WD1) and of the core-ventilation loop-A fire-detector (4001WD1), apply voltage between 15VDC and 28VDC and make sure that the insulation resistance value is more than 100 Mohms:
   (6) If the resistance value is between 0 ohms and 178 ohms:
  • On the responders, do a check of the equivalent resistance value between, ASM 261201:
    . Pin A/C and A/A of the core-ventilation loop-A fire-detector (4001WD1)
    . Pin A/C and A/A of the core-AGB loop-A fire-detector (4002WD1)
    . Pin A/C and A/A of the engine-1-pylon loop-A fire-detector (3WD1).
     (a) If the resistance values are null:
     (b) If the resistance values are corrects:
  • Do a check of the wiring between, ASM 261201:
    . Pin A/C of the core-ventilation loop-A fire-detector (4001WD1) and the first terminal-block
    . Pin A/A of the core-ventilation loop-A fire-detector (4001WD1) and the first terminal-block
    . Pin A/C of the core-AGB loop-A fire-detector (4002WD1) and the first terminal-block
    . Pin A/A of the core-AGB loop-A fire-detector (4002WD1) and the first terminal-block
    . Pin A/C of the engine-1-pylon loop-A fire-detector (3WD1) and the first terminal-block
    . Pin A/A of the engine-1-pylon loop-A fire-detector (3WD1) and the first terminal-block.
       1 If the wiring is not correct:
  • Repair it (them).
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
       2 If the wiring is correct:
  • Replace the terminal-block .
  • Connect connector 2WD1-A to the engine 1 FDU (2WD1).
Subtask 26-12-00-810-151-A ** ON A/C NOT FOR ALL
C. For the fault message related to engine-1 loop-B AGB, refer to the (Ref. TSM TASK 26-12-00-810-855).
[Rev.8 from Aug 2018] 2026.04.04 04:27:14 UTC
"WTRUIB" 2025