DOC AIRBUS | AMM A320FRemoval of the Magnetic Chip Detector [IAE]
TASK 79-22-45-000-010-A
Removal of the Magnetic Chip Detector
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 79-22-45-941-050-A ** ON A/C NOT FOR ALL
Subtask 79-22-45-020-050-B ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 03:40:35 UTC
Removal of the Magnetic Chip Detector
WARNING:
DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
- FLUSH IT AWAY WITH CLEAN WATER
- GET MEDICAL AID.
WARNING:
BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.
CAUTION:
DO NOT LET ENGINE FUEL OR OIL FALL ON THE ENGINE. UNWANTED FUEL OR OIL MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FUEL OR OIL CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 400 | POWER PLANT, NACELLES AND PYLONS |
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 437CL, 438AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 447CL, 448AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 71-13-00-010-010-A | Opening of the Fan Cowls 437AL(447AL),438AR(448AR) |
| TASK 79-00-00-200-010-A | Inspection of the Oil System |
Master Magnetic Chip DetectorSubtask 79-22-45-941-050-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
Subtask 79-22-45-010-050-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
B. Get access to the Magnetic Chip Detector (MCD).
(1) To get access to the master MCD only, open the inspection door on the left fan cowl.
(a) FOR [1000EM1] (ENGINE-1)
437CL
(b) FOR [1000EM2] (ENGINE-2)
447CL
(2) To get access to all the MCDs,
open the left and right fan cowls. (Ref. AMM TASK 71-13-00-010-010)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
4. Procedure(1) To get access to the master MCD only, open the inspection door on the left fan cowl.
(a) FOR [1000EM1] (ENGINE-1)
437CL
(b) FOR [1000EM2] (ENGINE-2)
447CL
(2) To get access to all the MCDs,
open the left and right fan cowls. (Ref. AMM TASK 71-13-00-010-010)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
Subtask 79-22-45-020-050-B ** ON A/C NOT FOR ALL
A. Remove the MCD
Post SBE 79-0042
(1) Push the MCD (4) into its housing (6) and turn counterclockwise. Pull and remove the MCD.
Subtask 79-22-45-210-050-A ** ON A/C NOT FOR ALL Subtask 79-22-45-020-053-C ** ON A/C NOT FOR ALL Post SBE 79-0042
(1) Push the MCD (4) into its housing (6) and turn counterclockwise. Pull and remove the MCD.
C. Remove the seal ring
Post SBE 79-0042
(1) Remove the seal ring (5) from the MCD and discard it.
Post SBE 79-0042
(1) Remove the seal ring (5) from the MCD and discard it.