Inspection/Check of the Oil Tank [CFMB]

TASK 79-11-10-200-002-A
Inspection/Check of the Oil Tank

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
TASK 79-00-00-210-003-A	Visual Inspection of the Oil System
TASK 79-11-10-300-003-A	Replacement of the O-ring of the Oil Tank Filler Cap
TASK 79-11-10-300-004-A	Replacement of the O-ring of the Oil Cap Assembly

3. Job Set-up
Subtask 79-11-10-941-057-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 79-11-10-010-058-A ** ON A/C NOT FOR ALL

B. Open the fan cowl doors: (Ref. AMM TASK 71-13-00-010-040)
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR

4. Procedure
Subtask 79-11-10-210-052-A ** ON A/C NOT FOR ALL

A. Inspect the following :

INSPECT/CHECK	MAXIMUM SERVICEABLE LIMITS	REMARKS
1.Tank envelope for :
Nicks, scratches in metal	Max. of 3 nicks or scratches 0.015 in. (0.38 mm) deep, 0.375 in. (9.53 mm) long, non joining provided damage cannot be felt with 0.030 in. (0.76 mm) ball scriber.
Dents	Any number not breaking metal surface or affecting the capacity of the tank.
Cracks in metal	None permitted

Subtask 79-11-10-210-053-A ** ON A/C NOT FOR ALL

B. Check for leakage

INSPECT/CHECK	MAXIMUM SERVICEABLE LIMITS	REMARKS
1.Check for leakage at following locations (Ref. AMM TASK 79-00-00-210-003):
At parting line flanges	None permitted
At fittings	None permitted	Check torque on fittings
Body of tank	None permitted
Defective or leaky O-ring seal of oil tank filler cap	Not serviceable	Repair (Ref. AMM TASK 79-11-10-300-003) or (Ref. AMM TASK 79-11-10-300-004).

5. Close-up
Subtask 79-11-10-410-057-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors: (Ref. AMM TASK 71-13-00-410-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 03:39:03 UTC